Manual Sym JET EUROX 50 (page 27 of 31) (English)

517190

Zoom out

Zoom in

1/31

11. INSPECTION AND MAINTENANCE BEFORE RIDING

CHECKING AND CHANGING FUSES

Turn off ignition switch, and check fuses if they are intact. Replace the blown fuse with a new one having

the same specified amperage rating (7A). Using a fuse of more than 7 amperes, a brass or iron wire to

replace a blown fuse is strictly prohibited to avoid damaging the electrical system and the circuit.

y Remove the battery cover screws, and open the battery cover. Fuses are installed in the fuse box

located by the battery.

y Fuses must be firmly secured with wire connectors when replacing.

y Use only parts having the specified specification to replace electrical components such as light bulbs.

Using parts not having the specified specifications for replacement may cause the fuse to blow and

over-discharge the battery.

y Avoid spraying water directly on or around fuse box when washing the motorcycle.

y Take your scooter to your dealer for an inspection if a fuse is blown by unknown causes.

【REMOVE】【INSTALLATION】

CHECKING THE TURN SIGNAL LIGHTS AND HORN

y Turn the ignition switch key to “ON” position.

y Turn on the turn signal light switch, and make sure that the front & rear and left & right signal lights

flashes and also check if the warning buzzer sounds.

y Check turn signal light covers if they are dirty, crack, or loosen.

y Press horn button to check if it works.

CHECKING THE FRONT AND REAR LIGHTS

y Turn the ignition switch key to “ON” position, start the engine and then turn on the front light switch.

Check if front and rear lights come on.

y Check the brightness and direction of front light by projecting the light on the wall to see if it is correct.

y Check the front light cover if it is dirty, crack, or loosen.

CHECKING THE BRAKE LIGHT

y Turn the ignition switch key to “ON” position, hold the hand-braking levers for front and rear wheels.

Check if the brake lights come on.

y Check the brake light cover if it is dirty, crack, or loosen.

Wire

Fuse connectors

Fuse

Press in from above

CAUTION:

y Specified specification bulbs should be used for turn signal lights. Otherwise, the normal operation

of turn signal lights will be affected.

y Switch on the turn signal before changing lanes or marking a turn to inform others of your intent.

y After changing lanes or making a turn, switch of turn signal immediately by pressing the reset

button. This button is located in the center of the turn signal switch.

CAUTION:

y Use only SANYANG specified bulbs, do not use bulbs with different specifications to avoid

damaging electrical system, burning out bulbs, and discharging the battery.

y Do not modify or add other electrical components to your scooter. This may prevent an over load

or short circuit which may result in a fire some cases.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Sym JET EUROX 50 in the language / languages: English as an attachment in your email.

The manual is 0,71 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Sym JET EUROX 50 Manual

Product: