Manual Steinel BHG 360 Li-Ion (page 6 of 8) (All languages)

593381

Zoom out

Zoom in

1/8

Rechargeable battery

■ Protect the rechargeable battery and the tool from heat, mois-

ture, water, e.g. also from permanent sunlight and fire. It could

explode.

■ The rechargeable battery must only be removed in the way

described in these instructions.

■ Do not open the tool or the rechargeable battery. This could

cause a short circuit. Please contact your retailer if you

encounter any problems.

■ Do not touch any electrolyte fluid that has escaped. Do not get

electrolyte fluid in your eyes. Immediately move tool away from

naked flames or sources of heat. Immediately remove contam-

inated clothing.

■ If electrolyte does escape from the battery, the following action

is necessary:

Contact with eyes:

Immediately rinse eyes with copious quantities of clean water,

such as tap water, but do not rub. Seek medical attention.

Failure to take the appropriate action can result in loss of sight.

Contact with skin:

Immediately wash the areas affected with copious quantities of

clean water, e.g. tap water, or skin irritation may occur. If the

chemical penetrates clothing, take off clothing immediately and

wash the skin with water. If irritation persists after washing,

seek medical attention.

Inhalation:

If the rechargeable battery is damaged or used improperly,

vapours or electrolyte fluid may escape. Provide fresh air and

seek medical attention if you feel unwell or discomfort occurs.

The vapours may cause respiratory irritation.

■ The lithium-ion rechargeable battery can be recharged at any

time without shortening its lifespan. Interrupting the charge

cycle will not damage the rechargeable battery.

■ When taking out of use for a long time, put the tool away with

battery charged. This will prolong the life of the lithium-ion

rechargeable battery.

■ When not in use, keep the rechargeable battery away from

paper clips, coins, keys, nails, screws or other small metal

objects that could short-circuit the contacts. Short-circuiting

the rechargeable battery contacts can cause burns or fire.

■ Do not short-circuit the rechargeable battery. It could explode.

■ Make sure the tool is switched off before fitting the recharge-

able battery. Inserting a rechargeable battery into a power tool

that is switched on can lead to accidents.

■ Only charge rechargeable batteries in chargers recommended

by the manufacturer. A charger suitable for specific recharge-

able batteries presents a risk of fire if it is used for charging

other rechargeable batteries. Only use rechargeable batteries

intended for use in power tools. The use of other rechargeable

batteries can result in injuries and the risk of fire.

■ Protect the rechargeable battery from moisture and water.

Charge the rechargeable battery at a temperature ranging from

0 °C to 45 °C. Do not, for example, leave the rechargeable

battery inside a car during summer. From time to time, clean

the rechargeable battery's ventilation slots with a soft, clean

and dry paintbrush.

Transport

■ The rechargeable battery conforms to UN manual ST/SG/AC.

10/11/Rev.3 Part III, sub-section 38.3. It is equipped with an

effective means to prevent internal pressure build-up and short

circuit as well as a means to preclude violent rupture and dan-

gerous reverse current flow. The lithium-equivalent quantity

contained in the rechargeable battery is below the relevant limit

values. Therefore, the rechargeable battery is not subject to

national or international dangerous goods regulations either as

an individual component or fitted in a device. However, these

regulations may become relevant if transporting several

rechargeable batteries. In this case, it may be necessary to

observe specific conditions (e.g. in relation to packaging).

■ The STEINEL BHG 360 li-ion power tool is intended for shap-

ing and welding plastic as well as for heating shrink tubing.

It can also be used for soldering and tin-plating as well as

ungluing bonded joints.

■ The LS - 36 V charger is only suitable for charging the

STEINEL li-ion 10 IMR 18/65-2 rechargeable battery

(type 0938).

Keep these safety precautions in a safe place together with the tool.

Technical specifications

Nominal voltage: 36 V, li-ion rechargeable battery

Output: 300 W

Temperatures: 400 °C without nozzle /

500 °C with 7 mm reduction nozzle (included)

Max. airflow rate: 100 l / min. max.

Running time: 15 min.

Charger: LS - 36 V

Battery charging voltage: [V=] 36

Charging current: [A] 4.0

Permissible

charging temperature range: [°C] 0 – 45

Charging time for rechargeable

battery capacitance, approx.: 2.6 Ah 30 min. (75%) 60 min. (100%)

Weight according to

EPTA procedure : 01 / 2003 [kg] 1.0

Protection class: II

Please note the reference number shown on type plate of your charger. The trade names of some chargers may vary.

Battery charger

■ Keep the charger out of rain and do not expose it to moisture.

The risk of electric shock will be increased if water is allowed

to penetrate the charger.

■ Do not charge rechargeable batteries of other brands. The

charger is only suitable for charging the STEINEL li-ion 10 IMR

18/65-2 rechargeable battery within the stated voltage range.

They could otherwise catch fire or explode.

■ Keep the charger clean. Soiling may present the risk of an

electric shock.

■ Damaged chargers, cords and plug will increase the risk of

electric shock. Always check the charger, power cord and plug

before use. Do not use the charger if you notice any damage.

Do not open the charger yourself and only have it repaired by

a qualified electrician who must only use genuine replacement

parts.

■ Do not operate the charger on highly combustible surfaces

(e.g. paper, textiles etc.) or in combustible environments. There

is a risk of fire from the heat produced by the charger while it

is charging.

For your safety

The thermal cut-out shuts the tool down if it is overloaded.

Using the LS - 36 V charge station

Observe mains voltage: The voltage of the power source must

match the specifications shown on the type plate of your hot air

tool. Tools showing 230 V can also be operated on 220 V.

The charge cycle begins as soon as the charger is plugged in and

the rechargeable battery is inserted

into the charging slot

The intelligent charging process automatically identifies the

charge state of the rechargeable battery and charges it with the

charge current optimised for battery temperature and voltage.

This protects the rechargeable battery and always keeps it fully

charged when kept in the charger.

What the indicators mean

Charge cycle monitoring is signalised by LED

indicators

Fast charge mode

The fast charge mode is signalised by flashing

green LED indicator

. While charging,

the 3 green LED's on the rechargeable battery

light up in succession and then briefly go out.

The rechargeable battery is fully charged when

the 3 green LED's are permanently lit. The 3

green LED's go out again about 5 minutes after the recharge-

able battery has been fully charged.

The fast charge mode is only possible when the rechargeable

battery is at a temperature of between 0 °C and 45 °C.

Battery charged

Green LED indicator

lights up permanently

to signalise that the rechargeable battery is

fully charged. An acoustic signal lasting approx.

2 seconds is also given to signalise that the

rechargeable battery is fully charged.

The rechargeable battery can now be removed

for immediate use.

When the rechargeable battery is not inserted, the green LED

indicator

lights up permanently to signalise that the charger

is plugged into the power supply and ready for use.

Proper use

- 11 -- 10 -

Safety warnings

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Steinel BHG 360 Li-Ion in the language / languages: All languages as an attachment in your email.

The manual is 1,82 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Steinel BHG 360 Li-Ion Manual

Product: