805836

Stanley SFMCW221 Fatmax V20 Manual

9
Zoom out
Zoom in
Previous page
1/12
Next page
9
ENGLISH
(Original instructions)
Use
Warning! Let the tool work at its own pace. Do not overload.
Switching on and off
u To switch the tool on, depress the on/off switch (1) at the
"I" position.
u To switch the tool off, depress the on/off switch (1) at
the"O" position.
Variable-Speed Dial
To operate the tool, select the speed setting you wish with the
speed dial (8) , and press the ON/OFF switch.
The speed setting can be adjusted either with the tool ON or
OFF.
Warning! Because the tool has a separate speed dial for
setting the speed, the tool will start at the speed where the
variable speed dial is set. Always ensure switch is off in the
"O" position before installing the battery pack.
Warning! Be sure to select the proper speed for your
sanding operation. If in doubt about the proper speed for your
operation, test the performance at low speed settings and
gradually increase until a comfortable speed is found.
Operation (Fig.H)
Grasp the sander as shown in gure H and turn it ON. Move it
in long, sweeping strokes along the surface, letting it do
the work.
Pushing down on the tool while sanding actually slows the
removal rate and produces an inferior quality nish.
Check your work often. Sander is capable of removing
material rapidly especially with coarse paper.
Precautions to take when sanding paint
Sanding of lead based paint is NOT RECOMMENDED due to
the difculty of controlling the contaminated dust. The greatest
danger of lead poisoning is to children and pregnant women.
Since it is difcult to identify whether or not a paint contains
lead without a chemical analysis, we recommend the following
precautions when sanding any paint:
Personal safety
u No children or pregnant women should enter the work
area where the paint sanding is being done until all clean
up is completed.
u A dust mask or respirator should be worn by all persons
entering the work area. The lter should be replaced daily
or whenever the wearer has difculty breathing. See your
local hardware store for the proper EN14683-approved
dust mask.
u NO EATING, DRINKING or SMOKING should be done
in the work area to prevent ingesting contaminated paint
particles.
Workers should wash and clean up BEFORE eating,
drinking or smoking. Articles of food, drink, or smoking
should not be left in the work area where dust would settle
on them.
Environmental safety
u Paint should be removed in such a manner as to minimize
the amount of dust generated.
u Areas where paint removal is occurring should be sealed
with plastic sheeting of 4 mils thickness.
u Sanding should be done in a manner to reduce tracking of
paint dust outside the work area.
Cleaning and disposal
u All surfaces in the work area should be vacuumed and
thoroughly cleaned daily for the duration of the sanding
project. Vacuum lter bags should be changed frequently.
u Plastic drop cloths should be gathered up and disposed
of along with any dust chips or other removal debris.
They should be placed in sealed refuse receptacles and
disposed of through regular trash pick-up procedures.
During clean up, children and pregnant women should be
kept away from the immediate work area.
u All toys, washable furniture and utensils used by children
should be washed thoroughly before being used again.
Dust Collection (Fig.I, J)
Warning! Collected sanding dust from sanding surface
coatings (polyurethane, linseed oil, etc.) can self=ignite and
cause re. To reduce risk, strictly follow sander manual and
coating manufacturer’s instructions.
u The dust bag should be emptied after every 10 minutes of
sanding.
u To attach the dust bag to the sander, line up the grooves
(14) on the side dust bag collar (15) with the dust bag
locks (16) on the dust port (17) .
u Slide the dust bag onto the dust port and turn the dust bag
clockwise to lock it in place as shown in Figure I.
u To remove, turn the dust bag counterclockwise and slide
the dust bag off.
u To empty the dust bag, remove it from the dust port
and dump the sanding debris into an appropriate trash
receptacle as shown in Figure J.
Connecting a vacuum cleaner)
u Insert the hose of the vacuum cleaner into the dust port
(17).
Accessories
Warning! Since accessories, other than those offered by
STANLEY FATMAX, have not been tested with this product,
use of such accessories with this tool could be hazardous.
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley SFMCW221 Fatmax V20 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley SFMCW221 Fatmax V20 in the language / languages: English as an attachment in your email.

The manual is 2.15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info