Manual Stanley SFMCW221 Fatmax V20 (page 8 of 12) (English)

805836

Zoom out

Zoom in

1/12

ENGLISH (Original instructions)

u Plug the charger (12) into an appropriate outlet before

inserting battery pack (6).

u The green charging light (12a) will blink continuously

indicating that the charging process has started.

u The completion of charge will be indicated by the green

charging light (12a) remaining ON continuously. The

battery pack (6) is fully charged and may be removed and

used at this time or left in the charger (12).

u Charge discharged batteries within 1 week. Battery life will

be greatly diminished if stored in a discharged state.

Charger LED Modes

Charging:

Green LED Intermittent

Fully Charged:

Green LED Solid

Hot/Cold Pack Delay:

Green LED Intermittent

Red LED Solid

Note: The compatible charger(s) will not charge a faulty

battery pack. The charger will indicate a faulty battery pack by

refusing to light.

Note: This could also mean a problem with a charger. If the

charger indicates a problem, take the charger and battery

pack to be tested at an authorized service centre.

Leaving the battery in the charger

The charger and battery pack can be left connected with the

LED glowing indenitely. The charger will keep the battery

pack fresh and fully charged.

Hot/Cold Pack Delay

When the charger detects a battery that is too hot or too

cold, it automatically starts a Hot/Cold Pack Delay, the green

LED (12a) will ash intermittently, while the red LED (12b)

will remain on continuously, suspending charging until the

battery has reached an appropriate temperature. The charger

then automatically switches to the pack charging mode. This

feature ensures maximum battery life.

Battery state of charge indicator (Fig. B)

The battery includes a state of charge indicator to quickly

determine the extent of battery life as shown in gure B. By

pressing the state of charge button (6a) you can easily view

the charge remaining in the battery as illustrated in gure B.

Installing and Removing the Battery Pack from

the tool

Warning! Make certain the lock-off button is engaged to

prevent switch actuation before removing or installing battery.

To install battery pack (Fig. C)

u Insert battery pack rmly into tool until an audible click is

heard as shown in gure C. Ensure battery pack is fully

seated and fully latched into position.

To remove battery pack (Fig. D)

u Depress the battery release button (7) as shown in

gure D and pull battery pack out of tool.

Attaching hook and loop sanding discs (Fig. E)

For best results, use STANLEY FATMAX accessories.

u To attach the sanding sheet (9) , carefully center the sheet

over the sanding pad (5) ensuring the holes in the disc

align with the holes in the pad and press the sheet rmly

in place.

u The hook and loop fastening system sanding sheet can be

easily removed by simply pulling it off. It can be reused as

desired.

Sanding sheet tips (Fig. F)

u Detach the two additional diamond-shaped tips (10) from

the sanding sheet (9).

Note: The diamond-shaped tip can be reversed and replaced

when worn.

u When the front part of the tip is worn, detach it from the

sheet, reverse it and press it onto the diamond-shaped

pad tip (11) again.

u When the whole tip is worn, remove it from the sanding

base and t a new tip.

Note: For optimal dust collection, ensure the correct type of

sanding paper is used.

Replacing Diamond Shaped Pad Tip (Fig. G)

When the sanding base tip (11) is worn, it can be replaced.

Spare parts are available from your dealer.

u Remove the screw (13) .

u Replace the worn part.

u Fit and tighten the screw.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Stanley SFMCW221 Fatmax V20 in the language / languages: English as an attachment in your email.

The manual is 2.15 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Stanley SFMCW221 Fatmax V20 Manual

Product: