622599
5
Zoom out
Zoom in
Previous page
1/100
Next page
5
ENGLISH
(Original instructions)
16. Remove adjusting keys and wrenches
Always check that adjusting keys and wrenches are removed
from the tool before operating the tool.
17. Avoid unintentional starting
Do not carry the tool with a nger on the switch. Be sure that
the tool is switched off before plugging in.
18. Use outdoor extension cables
Before use, inspect the extension cable and replace if
damaged. When using the tool outdoors, only use extension
cables intended for outdoor use and marked accordingly.
19. Stay alert
Watch what you are doing, use common sense and do not
operate the tool when you are tired.
20. Check for damaged parts
Before use, carefully check the tool and mains cable for
damage. Check for misalignment and seizure of moving
parts, breakage of parts, damage to guards and switches and
any other conditions that may affect its operation. Ensure that
the tool will operate properly and perform its intended function.
Do not use the tool if any part is damaged or defective. Do not
use the tool if the switch does not turn it on and off. Have any
damaged or defective parts replaced by an authorised Black
and Decker repair agent. Never attempt any repairs yourself.
21. Warning!
The use of any accessory or attachment or performance of
any operation with this tool other than those recommended in
this instruction manual may present a risk of personal injury.
22. Have your tool repaired by a qualied person
This tool is in accordance with the relevant safety regulations.
Have your tool repaired by an authorised Black and Decker
repair agent. Repairs should only be carried out by qualied
persons using original spare parts; otherwise this may result in
considerable danger to the user.
Additional safety instructions for chopsaws
u Always wear regular working gloves while operating this
tool.
u Keep hands away from the cutting disc. Never cut
workpieces that require manual action closer than 15 cm
from the rotating cutting disc.
u Do not cut workpieces less than 1.2 mm in thickness when
using the cutting disc supplied with this tool.
u Do not operate this tool without guards in place.
u Do not perform any operation freehand. Use the material
clamp to clamp the workpiece securely.
u Never reach in the back of the cutting disc.
u Always position the tool on a at, stable surface that is
well maintained and free of loose materials, e.g. chips and
cut-offs.
u Before using, inspect the cutting disc for cracks or aws.
Discard the cutting disc if a crack or aw is evident.
u Make sure the cutting disc is not contacting the workpiece
before the tool is switched on.
u In operation, avoid bouncing the cutting disc or giving it
rough treatment. If this occurs, stop the tool and inspect
the cutting disc.
u Do not operate the tool while standing in line with the
cutting disc. Keep other persons away from the work area.
u Be aware of cutting chips and the material being cut. They
may be sharp and hot. Allow cut off parts to cool before
handling.
u The spark deector becomes hot during use. Avoid
touching or adjusting the spark deector immediately after
operation.
u Switch off the tool and wait for the cutting disc to stop
before moving the workpiece or changing the settings.
u After switching off, never attempt to stop the cutting disc
by pressing against the side of the disc.
u Do not use cutting uids. These uids could ignite or
cause electrical shock.
u Check that the workpiece is properly supported.
u Use the cutting discs recommended by the manufacturer
only. Never use circular saw blades or any other types of
toothed blades.
u The max. allowable speed of the cutting disc must always
be equal to or greater than the no-load speed of the tool
specied on the nameplate.
u Do not use cutting discs that do not conform to the
dimensions stated in the technical data.
u Only use cutting discs that conform to EN12413.
u Ensure that the cutting disc is mounted correctly before
use.
u Let the tool run at no-load in a safe position for at least 30
seconds. If there is a considerable vibration or if any other
defect occurs, stop the tool and check it to determine the
cause.
u Do not use cutting discs for side grinding.
u Do not cut concrete, brick, tile or ceramic materials.
u Do not cut wood, plastic or synthetic materials.
u Do not cut cast-iron materials.
u Never cut magnesium materials.
u Do not cut electrically live material.
u Use this tool in a well-ventilated area. Do not operate the
tool near ammable liquids, gases or dust. Sparks or hot
chips from cutting or arcing motor brushes may ignite
combustible materials.
u Regularly clear the ventilation slots when working in dusty
conditions. If it should become necessary to clean the
slots, remember to unplug the tool rst.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley FME700 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley FME700 in the language / languages: All languages as an attachment in your email.

The manual is 4,77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info