644337
3
Zoom out
Zoom in
Previous page
1/8
Next page
2
3
CONTROL PANEL
1. MIC This is an XLR type connector for microphones.
The input level ranges from -60 to -20dB. This connector can
provide +48V phantom power for condenser microphones
when the phantom power is switched on.
2. LINE This is a balanced 1/4” phone jack for linking a line
level source The input level ranges from -40 to 0dB.
3. GAIN Use this knob to adjust the level of the input signal
to the optimal level. For optimal S/N ratio and dynamic
range, adjust this knob so that the peak indicator lights up
occasionally.
4. LOW CUT Push down this switch to activate a low cut  lter,
which allows high frequencies but attenuates low frequencies.
5. HI This control determines the level of high frequencies in
the output signal.
6. MID This control determines the level of mid frequencies
in the output signal.
7. LOW This control determines the level of low frequencies
in the output signal.
8. AUX (4M4S ONLY) Use this knob to control the signal
level sent from each channel to the AUX bus. It is set before the
channel fader, so it is not dependent on the fader position.
8. EFF (4M4S D ONLY)
Use this knob to control the signal level sent from each channel
to the built-in effects processor. It is set after the channel fader,
so it is dependent on the fader position. Adjust this knob when
you use effects processor on this channel.
9. PAN This control is used for distributing the signal level
of the channel feed to L / R buses. When the control is set to
12 o’clock, the signal is split evenly between L and R.
10. PEAK Indicator This LED signal will warn you of any
excessively high signal levels in the channel. The signal is
sampled in front of channel fader. It will light approximately
3dB before clipping and therefore give warning of a possible
overload.
11. LEVEL (Channel Fader)
This rotary fader controls the output level feed to the main bus
from the input channel, adjusting the volume balance between
the channels.
MONO CHANNEL SECTION
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stagg S MIX 4M4S D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stagg S MIX 4M4S D in the language / languages: English as an attachment in your email.

The manual is 1,65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Stagg S MIX 4M4S D

Stagg S MIX 4M4S D User Manual - German - 8 pages

Stagg S MIX 4M4S D User Manual - French - 8 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info