2
Radio remote control
• The radio remote control may only be used for equipment and systems in
which defective remote operation of the transmitter or receiver does not
constitute a risk to people, animals or property, or in cases where this risk
is eliminated by means of additional safety facilities.
• All persons operating the gate must be instructed that systems, where
there is a risk of injury or damage, may not be operated by remote con-
trol, or that such operation is only permitted, if all movements of the gate
can be supervised.
• The radio remote control device may only be used, if the operator can
fully supervise the movement of the device and if no persons or objects
are within the movement range of the gate.
• Keep the remote control device out of reach of children or animals and
prevent any inadvertent use.
• The operator of this radio-controlled equipment is not in any way protect-
ed against interference from other telecommunication systems and facili-
ties (e.g. other radio-controlled equipment that is licensed to operate at
the same frequency range). If such interference occurs, please contact
the local radio and telecommunications authority requesting a radioloca-
tion.
• Do not
use transmitters near locations or installations that are suscepti-
ble to radio interference (e.g. airports, hospitals).
Rating plate
The rating plate is located on the cover of the control unit housing.
Normal Use
After the drive system has been installed, the person responsi-
ble for the installation must complete an EU Declaration of
Conformity according to Machine Directive 98/37/EU and attach
a CE mark at the type plate of the drive.
This also applies in cases where the owner of the system is a
private person, as well as to manually operated gates that have
been upgraded with a drive. The above documents and the
instructions for installation and operation must be handed over
to the operator.
• The drives are exclusively designed for the opening and closing of gates.
Any other use is deemed improper. The manufacturer shall not be liable
for damages resulting from improper use. The user accepts sole respon-
sibility for any risks thereby incurred. Improper use shall void all warranty.
• Gates that are to be upgraded with an automatic drive system must com-
ply with the applicable standards and directives as amended,
e.g. EN 12453, EN 12604, EN 12605.
• Observe the safety distances according to EN 12604 between gate
leafs
and other objects.
• The drive system may only be operated if it is in proper working order.
Always follow standard safety procedures and adhere to the instructions
in this installation and operating manual.
• Immediately eliminate any defects that might impair the safety of the
equipment.
• The gate
leafs must only have minimum play at the hinges.
• The gate
leafs must be stable and warp-proof, i.e. they may not bend or
warp during opening or closing operation.
• The DSTA24 control and twist 200 drive systems may only be operated in
conjunction.
• The DSTA24 control and the twist 200 drives are designed for use in
private premises.
• The electric drive may only be used for the opening and closing of gates
with one or two
leafs.
Symbols
Indicates a potential risk. Failure to comply with the instructions
may result in serious injury or damage to property!
Information, useful advice.
Refers to the relevant illustration in the introduction or the main
text of this manual.
Safety instructions
General safety instructions
• All persons in charge of the installation, maintenance or operation of the
drive system must have read and fully understood these instructions.
• All instructions must be strictly adhered to. The manufacturer accepts no
liability for damage or malfunction resulting from non-compliance with the
instructions in this manual.
• Always comply with the statutory health and safety regulations and the
applicable standards.
• The installation and operation of the drive system is governed by the
following standards: EN 12453, EN 12604, EN 12605
• Prior to any work at the gate or drive, disconnect drive system from the
power supply and secure it against inadvertent reconnection or actuation.
• There is a risk of injury from crushing at the closing edges of the gates
or near the mechanical parts.
• Never operate the drive if you suspect that
it might be faulty or damaged.
• After installation and commissioning, all persons operating the drive must
be instructed on its functions and proper operation.
• Use only original spare parts, accessories and fixtures supplied by the
manufacturer.
Operation
• Ensure that the drive is never operated by children or persons who have
not been specifically instructed.
• When operating the gate, ensure that there are no persons, especially
children, animals or objects within its operating range.
• Only operate the gate with the remote control device when you have full
view of the gate.
• Never reach into the gate or any of its moving parts.
• Regularly inspect the safety devices. Immediately repair damaged or
defective parts. For details, see maintenance instructions.
• Only drive through the gate after it has been fully opened.
• Adjust the force tolerance to the minimum level.
• At gates with automatic closing mechanism, all edges must be secured
according to the applicable regulations and standards.
• Always remove the key to prevent unauthorised operation.
Storage
• The drive mechanism may only be stored indoors, in a dry, closed envi-
ronment at an ambient temperature of between -20°C and +50°C.
• Store drives in horizontal position.
