680852

Sommer twist 200 E Manual

25
Zoom out
Zoom in
Previous page
1/26
Next page
Troubleshooting
24
Fault Check yes/no Possible cause Remedy
Gate cannot be
opened/closed with a key
switch.
LEDs “Power” + “Imp./Geh”
on?
no • Cable connections loose
• Key switch defective
• Cable defective
• Retighten terminals
• Replace key switch
• Replace cable
yes • Pulser (key switch, remote
control) defective
• Check pulser and replace, if defective
Gate is stopped or
continues in reverse
motion.
Obstacle in operating
range?
no • Hinges too stiff
• Post has moved
• Limit switch settings incorrect
• Lubricate hinges
• Contact specialist
• Readjust limit switch
yes • Force cut-off triggered • Remove obstacle
Is gate leaf hopping at
start?
yes • Leaf not stable • Reinforce leaf
Is there strong wind? yes • Wind pressure too high • Simply open and close gate again
Gate does not fully open or
close.
Does gate stop before it
has reach its end position?
no • Leaf hinge incorrectly mount-
ed
• Change fittings at leaf
yes • Limit switch settings incorrect • Readjust limit switch
Incorrect closing sequence • Drive wires incorrectly
connected at terminals
• Read the instructions and reconnect drives to the the
control system
Drive cannot be properly
programmed
• DIP switch 8 is in position
OFF
• Limit switch set incorrectly;
the drive stops and is
reversed, or force cut-off.
• Set DIP switch 8 to ON
• Adjust
limit switch settings
Gate is not stopped by an
obstacle
• Gate is completing a pro-
gramming run
• Force tolerance set too high
• After the programming is completed, the force cut-off
is operational
• Reduce force tolerance, see "Adjusting force toler-
ance".
Drive touches the post Have dimensions A/B been
remeasured?
no • Incorrect dimension A or B • Readjust connection of drive at the post
yes • Limit switch settings incorrect • Readjust limit switch
Irregular gate movement • Incorrect dimensions A/B • Adjust dimensions, if possible
Pedestrian leaf cannot be
opened with remote control
device
• Remote control key not pro-
grammed
• Programme key, see section, see "Programming
remote control device".
Drive cannot be started Is LED “SH” flashing
rapidly?
yes • Position of jumper with
programmed force values
has been changed
• 1. Reset jumper to previous position
2. Reset control system
3. Position jumper as desired
4. Complete programming runs
… 25


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sommer twist 200 E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sommer twist 200 E in the language / languages: English as an attachment in your email.

The manual is 1,75 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sommer twist 200 E

Sommer twist 200 E User Manual - German - 36 pages

Sommer twist 200 E User Manual - Dutch - 33 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info