655956

Solo 879-12 Manual

50
Zoom out
Zoom in
Previous page
1/160
Next page
Safety provisions
ENGLISH 10
In addition to the safety provisions already listed, the following safety provisions also apply when working
with the motor device:
x Danger of poisoning! Once the engine is running, the power tool produces toxic exhaust that may be
invisible and odourless. Never start the power tool in closed rooms. Special danger also applies in
narrow situations, troughs or ditches. Only work here when it is absolutely certain that there is sufficient
air exchange and that no toxic gases may accumulate.
x Increased danger of fire! Do not smoke at the workplace – not even in the proximity of the power tool.
x Secure the workplace against accidental access by third parties, e.g. with warning signs. Only persons
involved and wearing adequate protective equipment and clothes must be present within 30 metres
[approx. 30 yards] around the working area.
x Check the site of deployment for possible dangers.
– Spark formation during cutting means that work must never be performed close to potentially
explosive gases of liquids, or easily flammable objects.
– No electrical lines, water or gas pipes or flammable substances must be placed in the area to be cut.
– Objects that may fall off or topple over during work must be secured or removed from the working
environment first.
– Prepare the workplace so that secure operator mobility is possible.
x The work piece to be cut must be free of foreign bodies such as screws, nails or stones.
x When working in residential areas, observe the noise protection provisions.
x Work carefully, considerately and calmly and do not endanger others.
– Ensure good sight and light conditions.
– Always remain within calling distance of other persons who may administer first aid in emergencies.
– Schedule work breaks.
– Be attentive towards possible danger sources and take the corresponding preventive measures.
Consider that use of hearing protection limits perception of sounds. Signal sounds, calls, etc. that
announce danger may also be missed.
– Observe tripping dangers and obstacles. Never work on unstable grounds.
– Always hold the power tool with both hands and always ensure a safe and firm stance.
– Never cut standing on a ladder.
– Guide the power tool so that no body part is located in the extended swivel range of the cut-off
wheel.
– Do not hold the work piece in your hand and bring it into contact with the wheel.
– Process only the work piece to be cut with the rotating cut-off wheel.
Never touch the floor or other objects with the cut-off wheel running.
– Do not use the power tool to level off and shovel away objects.
x Switch off the engine when the power tool starts to behave noticeably differently.
x Danger of burns! Do not touch the muffler while it is still hot.
Danger of fire! Muffler radiates enormous heat.
Never put the hot power tool into dry grass or on flammable objects.
x Danger of hearing damage and burns!
Never work with defective muffler or without muffler.
3.9 During work
… 50 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Solo 879-12 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Solo 879-12 in the language / languages: English, German, French, Spanish as an attachment in your email.

The manual is 2,55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info