701724
11
Zoom out
Zoom in
Previous page
1/104
Next page
11
Always switch o tool and disconnect plug from power
source if the power supply cord or the extension cord is
cut, damaged or entangled (do not touch the cord
before disconnecting the plug)
Protect the (extension) cord from heat, oil and sharp
edges
Never use the cord for carrying, pulling or unplugging the
tool
Inspect the cord periodically and have it replaced by a
qualied person, if damaged
Inspect the extension cord periodically and replace it, if
damaged (inadequate extension cords can be
dangerous)
Do not use the tool if the switch does not turn it on and
o; always have a damaged switch repaired by a qualied
person
BEFORE USE
Be familiar with the controls and the proper use of the
tool
Check the functioning of the tool before each use and, in
case of a defect, have it repaired immediately by a
qualied person; never open the tool yourself
Before use, thoroughly inspect the area where the
tool is to be used and remove all solid objects that
could damage the shredding mechanism when
vacuuming (such as stones, broken glass, pieces of
metal)
When vacuuming, never use the tool without the
collection bag in place
Regularly check the collection bag for wear or damage
Never operate the tool with a defective guard or housing
Replace worn of damaged parts
Keep all nuts, bolts and screws tight to be sure that the
tool is in a safe working condition
DURING USE
Always keep the cord away from moving parts of the tool;
direct the cord to the rear, away from the tool
Operate the tool at a walking pace only (do not run)
Keep proper footing on slopes
Always ensure that the ventilation openings are kept clear
of debris
Take a secure stance when working (do not overreach,
especially when using steps or a ladder)
EXPLANATION OF SYMBOLS ON TOOL
3 Read the instruction manual before use
4 Wear protective glasses and hearing protection
5 Do not expose tool to rain
6 Pay attention to the risk of injury caused by flying
debris (keep bystanders a safe distance away from work
area)
7 Switch o and disconnect plug before cleaning/
maintenance or if (extension) cord is damaged or
entangled
8 Double insulation (no earth wire required)
9 Do not dispose of the tool together with household waste
material
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
Do not connect the blue (= neutral) or brown (= live) wire
in the cord of this tool to the earth terminal of the plug
If for any reason the old plug is cut o the cord of this tool,
it must be disposed of safely and not left unattended
USE
Assembly instructions 0
- mount supporting wheel K as illustrated
- ensure that tubes A and B, collection bag C and guide
handle D are assembled correctly and that shoulder
strap E is adjusted correctly before operating the tool
! firmly tighten all screws, bolts and nuts
Cord restraint !
- hook the loop in the extension cord over restraint F as
illustrated
- pull tight to secure the extension cord
On/o @
- switch on tool by pressing trigger switch G
- switch o tool by releasing trigger switch G
! before switching on the tool, ensure that it is not
in contact with any object
! after switching off the tool the motor continues to
run for a few seconds
• Blowing #
- select blowing mode with switch H as illustrated (only
when tool is switched off)
- with wheel J the maximum speed can be adjusted
from low to high (1-7) (0796)
• Vacuuming/shredding $
- ensure that collection bag C 2 is attached to the tool
(for mounting see 2)
- select vacuuming mode with switch H as illustrated
(only when tool is switched off)
- with wheel J the maximum speed can be adjusted
from low to high (1-7) (0796)
! do not vacuum solid objects such as stones,
broken glass, pieces of metal
- do not vacuum liquids
- do not vacuum large volumes of leaf material at one
time thus avoiding clogging of the vacuuming opening
and blocking of the shredder impeller
- the shredding intensity depends on the size of the leaf
material and its residual moisture
! when the tool suddenly stops, immediately switch
it off, disconnect plug from power source, and
remove any jammed material between shredder
impeller and housing
- regularly empty collection bag C 2 (the vacuum
capacity decreases considerably when the collection
bag is full)
Holding and guiding the tool %
! while working, always hold the tool at the
grey-coloured grip area(s)
- use supporting wheel K for easy guiding the tube
along the ground
- for optimal results keep a 5 - 10 cm distance to the
ground
Emptying of collection bag ^
! switch off the tool and disconnect the plug
- wait until the impeller comes to a standstill before
removing the collection bag from the tool
- open the zipper of the collection bag and empty it
completely
- compostic material does not belong with domestic
waste
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Skil 0796 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Skil 0796 in the language / languages: All languages as an attachment in your email.

The manual is 6,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info