681539

Skandia 1088025 - Digitale Multimeter Manual

4
Zoom out
Zoom in
Previous page
1/4
Next page
To avoid electrical shock or damage to the meter, do not get water
inside the case. Remove the test leads and any input signals before
opening the case.

To replace the Meter’s fuse (see the Fgure:
- Set the rotary switch to  range.
- Disconnect test leads from any inputs terminals.
- Use a screwdriver to unscrew the screws secured on the cover.
- Separate the battery cover from the bottom case.
- Replace the fuse only with specified ratings:
F 250mA/600V, F 10A/600V ø 6.3x30 (quick acting)
- Replace the cover and secure by the screws.
Before replacing the fuse, disconnect test leads from any circuit
under test. To prevent damage or injury, replace the fuse only with
specified ratings.

To replace the battery (see the Figure):
- When the battery voltage drop below proper operation range the
“ “ symbol will appear on the LCD display and the battery need to
be replaced.
- Turn the meter off and remove all test leads.
- Use a screwdriver to unscrew the two screws secured on the battery
cover and remove the battery cover.
- Replace the battery with one new 9V battery (6F22).
- Reinstall the battery cover and secure by the two screws.
Before replacing the battery, disconnect test leads from any circuit
under test, turn the meter off and remove test leads from the input
terminals.

(1)Test Leads one set
(2)Battery: 9V, 6F22 one piece
(3)Instruction Manual one piece







 
will be indicated when making a DCA measurement
- When only the figure “1” displayed, it indicates overrange
situation and the higher range has to be selected.
To avoid damage to the meter, use the proper terminals,
function, and range for your meassurement.

- When only the figure“OL” is displayed, it indicates overrange
situation and the higher range has to be selected.
- When the value scale to be measured is unknown beforehand, set
the range selector at the highest position
- “
” means the socket of INPUT maximum current is 250mA,
over current will destroy the fuse. 10A’s maximum current is 10A,
over current will destroy the fuse.

- Connect the black test lead to the COM jack and the red test lead
to the Ω jack.
- Set the transform switch at the Ω range position.
- Connect test leads across the resistance under measurement.
- You can get reading from LCD.
To avoid electrical shock and/or damage to the instrument,
disconnect circuit power and discharge all high-voltage capacitors
before measuring resistance.

- For measuring resistance above 1MΩ, the meter may take a few
seconds to stabilize reading. This is normal for high resistance
measuring. If the resistance being measured exceeds the
maximum value of the range selected or the input is not
connected, an overrange indication “1” will be displayed.

- Set the rotary switch to “
” range.
- Connect the black and red test leads to the COM and Ω terminals
respectively.
- Connect the red test lead to the anode, black test lead to the
cathode of the diode under testing.
- The meter will show the approx, forward voltage of the diode. If
the lead connection is reversed, only figure “1” displayed.
To avoid electrical shock and/or damage to the instrument,
disconnect circuit power and discharge all high-voltage capacitors
before testing diodes.

- Set the rotary switch to“ ” range.
- Connect the black and red test leads to the COM and Ω terminals
respectively.
- Connect the test leads to the resistance in the circuit being
measured.
- When the test lead to the circuit is below 50Ω a continuous
beeping will indicate it.
To avoid electrical shock and/or damage to the instrument, discon-
nect circuit power and dischange all high-voltage capacitors before
testing for Continuity.
Battery test
- Set the rotary switch to desired BATT range.
- Connect the black and red test leads to the COM and VΩ
terminals respectivery.
- Connect the test leads across the battery terminals under mea
surement.
- Read LCD display and determine if the battery is OK.


Periodically wipe the case with a damp cloth and mild detergent. Do
not use abrasives or solvents.
Dirt or moisture in the terminals can affect readings.
To clean the terminals:
- Turn the meter off and remove all test leads.
- Shake out any dirt that may be in the terminals.
- Soak a new swab with a cleaning and oiling agent
(such ad WD-40)
- Work the swab around in each terminal. The oiling agent insulates
the terminals from moisture-related contamination.
9
Skandia
©
Postbus 4341
7320 AH Apeldoorn
www.skandia.nl
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Skandia 1088025 - Digitale Multimeter at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Skandia 1088025 - Digitale Multimeter in the language / languages: English, Dutch as an attachment in your email.

The manual is 1,4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info