649341
5
Zoom out
Zoom in
Previous page
1/24
Next page
nl Inbedrijfstelling
Eerste opstart
1. Spanning inschakelen.
Tijdens de inbedrijfstelling blijft de regeling uitgeschakeld.
Alle veiligheidsfuncties zijn eveneens uitgeschakeld!
Zodra de regelaar opgestart is, verschijnt het menu
COMMI
(inbedrijfstelling) met knipperend submenu
Building Technologies 74 319 0428 0 c CE1G3101x1 02.06.2008 5/24
S
PARA
.
2. Selecteer met de navigatietoetsen (+/) het submenu
APPL ID
:
SET
PASS
3. Druk 2x op de OK-toets, waarna het startveld van het basistype
knippert.
4. Kies met de navigatietoetsen (+/
) het basistype en bevestig
door het indrukken van de OK-toets.
5. Kies, indien gewenst, het submenu
CONF
, om de configuratie te
kunnen aanpassen.
6. Kies, indien gewenst, het submenu
PARA
, om de instellingen
(defaultwaarde) te kunnen aanpassen.
7. Kies het submenu
TEST
, om de bedradingstest uit te voeren
(wordt aanbevolen!).
Controleer de in- en uitgangen. De uitgangen worden
gesimuleerd.
Attentie! De veiligheidsfuncties zijn uitgeschakeld.
8. Verlaat het menu
COMMIS
(inbedrijfstelling) door het indrukken
van ESC-toets. Het volgende scherm verschijnt:
COMMIS
PASS
9. Druk op de OK-toets.
De toepassing wordt gestart, alle opnemers worden
gecontroleerd, aanwezige opnemers worden voor latere
stroringsmeldingen gemarkeerd. Het volgende scherm verschijnt:
PASS
PARACOMMIS
SET
INFO
10. Kies met de navigatietoetsen (+/
) het menu
SET
en stel de
gewenste waarde instellingen in.
Indien gewenst, optimaliseert u de instellingen in het menu
PARA
(instellingen).
11. Druk 2x op de ESC-toets.
Bevindt de regelaar zich in „Normaal bedrijf“, dan verschijnt een
infopagina, bijv:
PASS
Opmerking:
Het menu
COMMIS
(inbedrijfstelling) is alleen op het
“wachtwoordniveau” (Wachtwoord = 2) actief
Er zijn 3 toegangsniveau’s:
Gebruikerniveau
Seviceniveau
SERVICE
Wachtwoordniveau
PASS
Door het gelijktijdig indrukken van de ESC-toets en de OK-toets, is
een niveauwisseling mogelijk
In het menu SET zijn de instelwaarden altijd zichtbaar,
onafhankelijk van de gekozen applicatie.
Omdat de instellingen t.o.v. elkaar zijn begrensd, moeten niet
actieve instellingen zonodig ook worden versteld.
it Messa in servizio
Primo avviamento
1. Dare tensione all’apparecchio.
Durante la messa in servizio, il controllo dell’impianto è
disattivato.
Tutte le funzioni di sicurezza sono disattivate!
Quando la messa in servizio del regolatore è ultimata, la scritta
COMMIS
(messa in servizio) lampeggerà ed apparirà il
sottomenù
PARA
.
2. Selezionare il menù
APPL ID
utilizzando i tasti di navigazione
(+/-):
SET
PASS
3. Premere 2 volte il pulsante OK. Il campo predisposto per la scelta
dell’applicazione inizierà a lampeggiare.
4. Selezionare l’applicazione voluta tramite i tasti (+/
) e
confermare la scelta premendo il pulsante OK.
5. Se necessario, utilizzare il sottomenù
CONF
per adattare
l’applicazione scelta alle proprie esigenze.
6. Se necessario, utilizzare il sottomenù
PARA
per adattare le
impostazioni di fabbrica alle proprie esigenze.
7. Utilizzare il sottomenù
TEST
per fare il controllo dei collegamenti
elettrici. (operazione consigliata).
Verificare il corretto collegamento degli ingressi e delle uscite. Le
uscite possono essere simulate.
Attenzione! In questa fase le sicurezze non sono attive.
8. Uscire dal menù di messa in servizio
COMMIS
premendo il
pulsante ESC . Apparirà il seguente display:
COMMIS
PASS
9. Premere il pulsante OK .
L’applicazione impostata si avvierà, tutti i sensori saranno
verificati ed eventuali anomalie saranno segnalate da messaggi
di allarme. Apparirà il seguente menù:
PASS
PARACOMMIS
SET
INFO
10. Selezionare il menù
SET
tramite i tasti (+/
) e impostare i
setpoint richiesti. Se necessario, ottimizzare le impostazioni
utilizzando il menù
PARA
(impostazioni).
11. Premere 2 volte il pulsante ESC .
Se il regolatore sta funzionando regolarmente, apparirà la
seguente finestra di informazione:
PASS
Note:
Il menu
COMMIS
è attivo solo con il livello con password
(password = 2)
Ci sono 3 livelli di accesso:
Livello utente
Livello service
SERVICE
Livello Password Password level
PASS
Il cambio del livello avviene premendo contemporaneamente I tasti
ESC e OK .
Il menu SET visualizza sempre tutti i setpoint, indipendentemente
dalla applicazione selezionata.
Se richiesto, ciascun setpoint limite non attivo, deve essere
reimpostato.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Siemens RLU210 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Siemens RLU210 in the language / languages: All languages as an attachment in your email.

The manual is 1,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info