649341
3
Zoom out
Zoom in
Previous page
1/24
Next page
de Inbetriebnahme
Beim ersten Aufstarten
1. Spannung anlegen.
Während dieser Inbetriebnahme bleibt die Regelung
ausgeschaltet.
Sämtliche Sicherheitsfunktionen sind ebenfalls
ausgeschaltet!
Sobald der Regler hochgefahren ist, erscheint das Menü
COMMIS
(Inbetriebnahme) mit blinkendem Untermenü
PARA
.
2. Wählen Sie mit den Navigations-Tasten (+/
) das Untermenü
APPL
:
Building Technologies 74 319 0428 0 c CE1G3101x1 02.06.2008 3/24
ID
SET
PASS
3. Drücken Sie 2x die OK-Taste, worauf das Eingabefeld für den
Grundtyp blinkt
4. Wählen Sie mit den Navigations-Tasten (+/
) den Grundtyp und
bestätigen Sie diesen durch Drücken der OK-Taste
5. Wählen Sie ggf. das Untermenü
CONF
, um das Anpassen der
Konfiguration vorzunehmen
6. Wählen Sie ggf. das Untermenü
PARA
, um das Anpassen der
Parameter-Einstellungen (Defaultwerte) vorzunehmen
7. Wählen Sie das Untermenü
TEST
, um den Verdrahtungstest
durchzuführen (wird empfohlen!).
Prüfen Sie die Ein- und Ausgänge. Die Ausgänge werden
simuliert.
Achtung! Die Sicherheitsfunktionen sind ausgeschaltet
8. Verlassen Sie das Menü
COMMIS
(Inbetriebnahme) durch
Drücken der ESC-Taste. Es erscheint folgendes Hinweisbild:
COMMIS
PASS
9. Drücken Sie die OK-Taste.
Die Anwendung wird gestartet, alle Fühler werden überprüft,
vorhandene Fühler werden für spätere Störungsmeldungen
markiert. Es erscheint folgendes Menü:
PASS
SET
INFO
10. Wählen Sie mit den Navigations-Tasten (+/
) das Menü
SET
und nehmen Sie die Betreibereinstellungen für die Sollwerte vor.
Falls erforderlich, optimieren Sie Einstellungen im Menü
PARA
.
11. Drücken Sie 2x die ESC-Taste.
Befindet sich der Regler im Normalbetrieb, erscheint eine Info-
seite, z. B:
PASS
Hinweise:
Das Menü
COMMIS
(Inbetriebnahme) ist nur in der Passwort-
ebene (Passwort = 2) aktiv
Es gibt 3 Zugriffsebenen:
Endbenutzerebene
Serviceebene
SERVICE
Passwortebene
PASS
Bei gleichzeitigem Drücken der ESC-Taste und der OK-Taste, ist
ein Ebenenwechsel möglich
Im Menü SET sind alle Sollwerte immer sichtbar, unabhängig von
der gewählten Anwendung.
Weil sich die Sollwerte gegenseitig begrenzen, müssen die
nichtaktiven Sollwerte gegebenenfalls verstellt werden
en Commissioning
First startup
1. Switch on power supply.
During commissioning, the control system remains
deactivated.
All safety functions also remain deactivated!
When controller startup is completed, the
COMMIS
(commis-
sioning) menu with flashing
PARA
submenu appears.
2. Select the submenu
APPL ID
with the navigation buttons (+/
):
SET
PASS
3. Press the OK button twice. The entry field for the basic type
starts flashing.
4. Select the basic type with the navigation buttons (+/
) and
confirm it by pressing the OK button.
5. If required, select the
CONF
submenu to adapt the configuration.
6. If required, select the
PARA
submenu to adapt the parameter
settings (default values).
7. Select the
TEST
submenu to make the wiring test
(recommended!).
Check the inputs and outputs. The outputs will be simulated.
Caution! Safety functions are deactivated.
8. Quit the
COMMIS
menu by pressing the ESC button. The
following display appears:
COMMIS
PASS
9. Press the OK button.
The application is started, all sensors will be checked and
existing sensors will be highlighted for future fault status
messages. The following menu appears:
PASS
PARACOMMIS
SET
INFO
10. Select the
SET
menu with the navigation buttons (+/
) and
make the setpoint adjustments as required by the building
operator. If required, optimize the settings on the
PARA
menu.
11. Press the ESC button twice.
If the controller is in normal operation, the info page will appear,
e.g.:
PASS
Notes:
The
COMMIS
menu is only active on the password level
(password = 2)
There are 3 access levels:
Enduser level
Service level
SERVICE
Password level
PASS
The level can be changed by pressing the ESC and OK buttons
simultaneously
The SET menu always shows all setpoints, independent of the
selected application.
Since the setpoints limit one another, the nonactive setpoints must
be readjusted, if required
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Siemens RLU210 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Siemens RLU210 in the language / languages: All languages as an attachment in your email.

The manual is 1,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info