465406
11
Zoom out
Zoom in
Previous page
1/14
Next page
11 / 14
Siemens REV24.. room temperature controller CE1N2205en
Building Technologies 24.04.2008
Reset
User-defined settings:
Press
, and simultaneously for 3 seconds:
This resets all temperature and time settings of the program selection slider to default
values (see also "Factory settings" in the operating instructions). The expert settings
remain unchanged.
The clock starts at 12 p.m., the date on 01-01-08 (01 January 2008).
During the reset, all display fields are lit and can be checked accordingly.
All user-defined settings plus expert settings:
Press the DIP switch reset button
ON
1 342
2211Z32
567 89
, and simultaneously for 5
seconds:
After the reset, all factor settings are reloaded. This applies to the program selection
slider as well as to the expert settings.
Engineering
Mount the room temperature controller in the main living room
Select the mounting place so that the sensor can acquire the air temperature in the
room as accurately as possible and without being influenced by solar radiation or
other heat or refrigeration sources
Mounting height is approx. 1.5 m above the floor
You can mount the unit on most commercially available recessed conduit boxes or
directly on the wall
Begin installation by first attaching and wiring the base. You can mount the base on
most commercially available recessed conduit boxes or directly on the wall. Then
insert the controller from top to bottom into the base.
For more information, see the installation instructions supplied with the unit.
Comply with all local regulations on electrical installation
Wire separately the remote control contact T1 / T2 using a separate, shielded cable
Remove from the batteries the battery transit tab designed to prevent premature
activation of the unit: Select desired language by
or . Confirm by .
You can change the control characteristics using the DIP switch on the rear of the unit
Set any thermostatic radiator valves to their fully open position, if present in the
reference room
Recalibrate the temperature sensor (see "Sensor calibration") if the displayed room
temperature does not match the room temperature measured
This is a software class A controller designed for use at a normal degree of pollution.
Mounting and
installation
Commissioning
Notes
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Siemens REV24 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Siemens REV24 in the language / languages: English as an attachment in your email.

The manual is 0,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Siemens REV24

Siemens REV24 User Manual - German - 2 pages

Siemens REV24 User Manual - Dutch - 2 pages

Siemens REV24 User Manual - French - 2 pages

Siemens REV24 Installation Guide - All languages - 50 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info