465406
10
Zoom out
Zoom in
Previous page
1/14
Next page
10 / 14
Siemens REV24.. room temperature controller CE1N2205en
Building Technologies 24.04.2008
Access to the expert level
Set the program selection slider to RUN. Press and simultaneously for 3 seconds, release the buttons, and
within 3 seconds press and hold down
and simultaneously for 3 seconds, release , and press for another 3
seconds. This releases the settings at the expert level.
is displayed.
The display first shows language selection with Code 00. Press the buttons or to navigate the settings.
Confirm settings by pressing
.
Press the operating mode selector to exit the engineering settings.
Code list
This entry has no effect if the radio clock either is inactive or not available.
The time signal received from Frankfurt is shifted by the value set in Code 30 (time zone)
if the radio clock is active.
The time is always changed over at 2 a.m. on the Sunday preceding the set date if there
is no radio clock or if it is inactive. The time change is shifted by the value set in Code 30
(time zone) when the radio clock is active.
The time is always changed over at 3 a.m. on the Sunday preceding the set date if there
is no radio clock or if it is inactive.
Functional check
a) Check the display. If there is no display, check insertion and function of the batteries.
b) Operating mode “Continuous comfort mode“ , read displayed temperature.
c) REV.. in heating mode: Set the temperature setpoint higher than the displayed room
temperature (see operating instructions).
REV.. in cooling mode: Set the temperature setpoint lower than the displayed room
temperature (see operating instructions)
d)
The relay and, as a result, the actuating device must switch at the latest after one minute.
Symbol is displayed. If not displayed:
Check actuating device and wiring
It is possible that in heating mode the room temperature is higher than the set
temperature setpoint (and lower for cooling mode)
e) Set the temperature setpoint for operating mode “Continuous comfort mode“
to the
desired value
f) Select the desired operating mode
Function block
Code Name Factory setting Your setting
00
Language
English
01
Sensor calibration
off
Basic settings
02
Switching differential 2-point
0.5 °C
10
Illumination time
10 seconds
11
Background brightness
0
LCD
optimization
12
Contrast
0
30
Time zone
Deviation from time signal in Frankfurt
(Central European Time CET) (see Note 1)
0 hours
31
Start of daylight saving time (see Note 2)
March 31 (03-31)
Clock settings
32
End of daylight saving time (see Note 3)
October 31 (10-31)
Note 1:
Note 2:
Note 3:
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Siemens REV24 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Siemens REV24 in the language / languages: English as an attachment in your email.

The manual is 0,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Siemens REV24

Siemens REV24 User Manual - German - 2 pages

Siemens REV24 User Manual - Dutch - 2 pages

Siemens REV24 User Manual - French - 2 pages

Siemens REV24 Installation Guide - All languages - 50 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info