555876
1
Zoom out
Zoom in
Previous page
1/2
Next page
CE1B3035en / 11.06.2001 Subject to alteration Siemens Building Technologies / Landis & Staefa Division
Operating instructions
Landis & Staefa RDE…
RDE... - the temperature controller that allows you to set the ideal room temperature at the time you want. There
are several switching patterns available that can be set to your specific needs. You can either rely on the factory
settings or make settings that suit your personal needs.
Operation
Normal operation
Energy saving mode
Heating on
Replace
batteries
Warmer / colder
Setting the
temperature setpoints
and the time of day
Operating mode
selector
Batteries
(only with battery-powered versions)
3035Z11E
Display
Normal operation
Energy saving mode
Automatic operation
Continuous
normal operation
Continuous
energy saving mode
Day (1 = Monday / 7 = Sunday)
Measured room temperature
Time of day
Switching pattern
with time cursor
Confirmation
Settings
Time of day
Switching pattern
1...7
Weekday
Automatic operation/
switching pattern
settings
1.5V
'AAA'
1.5V
'AAA'
+-
Commissioning with quick startup
The controller is supplied with factory-set switching patterns, switching times and temperatures. To commission it,
proceed as follows:
1.5V 'AAA'
1.5V 'AAA'
Remove the black transit tabs from the two batteries. Check to see if the battery holder is in its correct position. The
controller switches itself on (only with batteriy-powered versions).
Press button .Press
+
-
to set the current time of day and confirm by pressing .
1...7
Press button
1...7
.Press
+
-
to set the current weekday and confirm by pressing .
(1 = Monday through 7 = Sunday).
Select the required operating mode with the operating mode selector.
Do you want to use automatic operation?
If that is the case, set the operating mode selector to
position
.
You use the 7-day time switch with automatic
changeover between normal operation and energy
saving mode / off.
Do you require continuous normal operation?
Move the operating mode selector to normal
operation. This ensures continuous heating to the
normal temperature. The display shows
.
Do you require continuous energy saving
mode?
Move the operating mode selector to energy saving
mode. This ensures continuous heating to the energy
saving temperature.
The display shows
.
Are your rooms too warm / too cold?
°C
+
-
By pressing these buttons, you increase or decrease
the room temperature setpoint in increments of 0.5
°C. The display first shows the newly selected
temperature and then the measured actual value
again.
These changes are valid only up to the next
switching point.
If, as a result of the factory settings, you always feel
either too warm or too cold, you should read-just the
temperature setpoint of normal operation
or
energy saving mode
to suit your needs.
Do you want to change the temperature set-points
of normal operation or energy saving mode?
or
Proceed as follows:
Press
or if you want to change the setpoint
of normal operation or of energy saving mode
The setpoint display starts flashing
Press the buttons to change the temperature
setpoints in increments of 0.5 °C.
By pressing
, the setting will be saved and
the entry mode quit
Important:
In energy saving mode, the unit can be set to OFF.
Proceed as follows:
Change the temperature setpoints to 5°C.
Press and hold
-
for 4 seconds.
Symbol
will not appear on the display.
Risk of frost!
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Siemens RDE - Landis Staefa at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Siemens RDE - Landis Staefa in the language / languages: English as an attachment in your email.

The manual is 0,42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Siemens RDE - Landis Staefa

Siemens RDE - Landis Staefa Quick start guide - English - 2 pages

Siemens RDE - Landis Staefa User Manual - German - 2 pages

Siemens RDE - Landis Staefa User Manual - Dutch - 2 pages

Siemens RDE - Landis Staefa User Manual - French - 2 pages

Siemens RDE - Landis Staefa Installation Guide - All languages - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info