620427
1
Zoom out
Zoom in
Previous page
1/2
Next page
Operating Instructions
RDD10.1DHW
RDD10.1DHW is a temperature controller that allows you to set the ideal room temperature at the
time you want and with independent control of DHW (Domestic Hot Water). There are 3 operating
modes available. You can either rely on the factory settings or make settings that suit your
personal needs.
Display
Operation and settings
Warmer / colder
setting the
temperature setpoints
DHW ON/OFF
Changing the
operating mode
between normal
operation, energy
saving and frost
protection mode
Room temperature or setpoint
Batteries
3033Z05en
1.5V
'AA'
1.5V
'AA'
+-
Normal operation
Energy saving mode
Heating ON
Room temperature
Replace batteries
DHW equipment ON
Frost protection mode
Commissioning
The controller is supplied with factory-set temperatures and operating mode. To commission
it, proceed as follows:
1,5 V
"AA"
1,5 V
"AA"
Remove the black transit tabs from the 2 batteries. Check to see if the battery holder
is in its correct position. The controller switches itself on.
Do you want to change the operating mode?
By pressing , you can change the operating
mode. The sequence is started from normal operation,
energy saving mode and frost protection, or vice versa.
Then, the setpoint of the selected operating mode will
be maintained.
In normal operation, the display shows
, in energy
saving mode, the display shows
, and in frost
protection mode, the display shows
.
Default operating mode is “Normal operation”.
When the unit is first powered up,
the display shows
.
Are your rooms too warm or too cold?
+
To increase or decrease the room temperature
setpoint in increments of 0.5 °C, proceed as follows:
Press
to select the operating mode
corresponding to the set point that you want to
change
Press
+
or once
The setpoint display starts flashing
Press these buttons again to change the
temperature setpoint in the range 5 ... 35 °C
5 seconds after the last push, the new temperature
setpoint will automatically be saved. The display stops
flashing and shows the room temperature currently
measured.
Note:
The setpoint in energy saving mode can be set to
0 °C. This means OFF or, in other words, the
controller is not active in energy saving mode and
symbol
will not appear on the display.
Risk of frost!
If you want to have frost protection, press
to
select frost protection mode, the display shows
and default value is 5 °C. If the room temperature falls
below the preset frost protection level, it will
automatically activate the heating output.
CE1B3033en / 18.11.2005 Subject to alteration Building Technologies / HVAC Products
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Siemens RDD10.1DHW at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Siemens RDD10.1DHW in the language / languages: English as an attachment in your email.

The manual is 0,29 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Siemens RDD10.1DHW

Siemens RDD10.1DHW User Manual - German - 2 pages

Siemens RDD10.1DHW Installation Guide - All languages - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info