620431
1
Zoom out
Zoom in
Previous page
1/6
Next page
Siemens Building Technologies / HVAC Products 4 319 2618 0 c CM1G1821X 10.08.2005 1/6
4 319 2618 0
G1821
1821Z12
4 109 2106 0
M16
DIN 7981-
2 x
St 4,2 x 22 - C
1821Z11
AQM63.0
1821Z01
AQM63.2
3 x
QAF63.2: 1 x AQM63.2
QAF63.6: 2 x AQM63.2
3 x
1821Z02
Montageort
Kapillarrohr in Luftrichtung nach dem ersten wassergefüllten und
frostgefährdeten Lufterwärmer installieren.
Montage
Vor der Montage des Frostfühlers, den Gehäusedeckel durch Lösen
der Befestigungsschraube abnehmen und die M16-Verschraubung
einsetzen, siehe Abb. 1.
Direktmontage auf die Kanal- oder Gerätewand
Gummizapfen (4 109 2106 0) in Gehäuserückseite einsetzen,
siehe Abb. 2
Gehäuse montieren, siehe Abb. 5
Direktmontage auf die Kanal- oder Gerätewand mit
Testschlaufe für Funktionstest, siehe Abb. 6
Hinweis: Die Temperatur an der Testschlaufe muss gleich oder
höher der Temperatur im Kanal sein!
Montage mit Montageflansch AQM63.0, für Luftkanäle mit
Isolierungen bis 70 mm Wandstärke, siehe Abb. 3
Kapillarrohrmontage im Luftkanal mittels Zubehör AQM63.2,
siehe Abb. 4
Das Kapillarrohr darf an den Wänden nicht scheuern (genügend
Distanzhalter verwenden)
Mindestabstand von der Kanalwand: ca. 50 mm
Das Kapillarrohr darf nicht geknickt werden; möglichst großer
Biegeradius
Elektrische Installation
Die örtlichen Vorschriften sind zu beachten
Verdrahtung nach Anlagenschaltplan ausführen
Inbetriebnahme
Verdrahtung nach Anlagenschaltplan überprüfen
Es sind keine Einstellungen notwendig
Funktionskontrolle
Funktionstestschlaufe, oder ein anderes mindestens 250 mm
langes Stück Kapillarrohr, mit Eiswasser auf 0 °C abkühlen,
siehe Abb. 7
Die Signalspannung, gemessen über die Klemmen B und M, muss
DC 0 V betragen (Messbereich: DC 0...10 V
0...15 °C)
Mounting location
Install capillary tube downstream from the first hot water heating coil
that may be exposed to frost.
Installation
Before installing the frost detector, remove the housing cover by
loosening the fixing screw and fit the M16 cable gland
(refer to Fig. 1)
Direct installation on the duct or equipment wall
Fit rubber (4 109 2106 0) grommet to the rear of the housing
(see Fig. 2)
Install the housing (see Fig. 5)
Direct installation on the duct or equipment wall with test loop
for functional test (see Fig. 6)
Note: the temperature at the test loop must be the same as or
higher than the temperature in the air duct!
Installation with mounting flange AQM63.0, for air ducts with
insulation up to 70 mm (see Fig. 3)
Installation of capillary tube in air duct by means of AQM63.2
accessory (see Fig. 4)
The capillary tube should not get into contact with the walls
(use an adequate number of spacers)
Minimum clearance from duct wall: approx. 50 mm
The capillary tube must not be sharply bent; the bending radius
should be as large as possible
Electrical installation
The local regulations must be complied with
Make wiring according to the plant connection diagram
Commissioning
Check wiring against the plant connection diagram
No settings are required
Functional test
Use ice water to cool the function test loop or another piece of
capillary tube of at least 250 mm length down to 0 °C (see Fig. 7)
The signal voltage, measured across terminals B and M, must be
DC 0 V (measuring range: DC 0...10 V
0...15 °C)
de
Gesamtanleitung
Frostfühler
en
General instructions
Frost Sensor
fr
Instructions générales
Sonde antigel
sv
Instruktioner
Frysgivare
nl
Algemene instructies
Vorstbeveiliging
it
Istruzioni generali
Regolatore antigelo
fi
Yleisohjeet
Jäätymissuoja-anturi
es
Instrucciones generales
Regulator anti-hielo
da
Install.- og monteringsvejl.
Frostføler
QAF63...
de
en
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Siemens QAF63..J at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Siemens QAF63..J in the language / languages: All languages as an attachment in your email.

The manual is 0,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Siemens QAF63..J

Siemens QAF63..J User Manual - English, German, Dutch, Danish, French, Italian, Swedish, Spanish, Finnish - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info