298545
7
Zoom out
Zoom in
Previous page
1/8
Next page
5
Gigaset A24 / AUS / A31008-M1640-C411-1-7619 / Wyoming_MT.fm / 26.10.2004
Activating/deactivating battery warning
tone
If this function is activated, a beep sounds in idle
status when the battery pack is almost flat.
To deactivate: MENU
¢ O 4 Q.
To activate: MENU
¢ O 4 1.
Resetting the handset
Restoring the factory settings of the handset will
not affect entries in the directory, the calls list or
the speed dial list or the handset's registration to
the base.
MENU ¢ OI ¢ RESET ? ¢ OK.
Appendix
Character set chart
Press the required key the number of times indi-
cated.
Specifications
Care
Wipe the handset with a damp cloth or an anti-
static cloth. Never use a dry cloth! This can cause
static!
Contact with liquid
If the handset has come into contact with liquid:
1 Switch the handset off and remove the bat-
tery pack immediately.
2 Allow the liquid to drain from the handset.
3 Pat all parts dry, then place the handset with
the battery compartment open and the keypad
facing down in a dry, warm place for at least
72 hours (not in a microwave, oven etc.).
4 Do not activate the handset again until it is
dry.
When it has fully dried out you will normally be
able to use it again.
Questions and answers
If you have any queries about the use of your tele-
phone, go to
www.siemens-mobile.com/gigasetcustomercare
for assistance 24/7. The table below contains a list
of common problems and possible solutions.
1 x 2 x3 x4 x5 x6 x
Q
+0-|?_
1
Spa
ce
1
R
# (appears in display as j)
P
*
/(),
Re-chargeable battery
pack
NiMH, 2xAAA Pack
Battery pack re-order
number
V30145-K1310-X359,
A5B00075178739
Battery pack capacity 550 mAh
Charging time approx. 10 hours in base,
approx. 5 hours in charging
shell
Calling time approx. 10 hours
Standby time approx. 170 hours (7 days)
Problem Cause Solution
Nothing
appears in the
display.
The handset is not
switched on.
Battery pack is
flat.
Press the end call
key a for approx.
5secs.
Charge/replace the
battery pack (page 2).
No response
to key press,
"HOLD KEY"
appears in the
display.
The keypad lock is
activated.
Press the hash key
R
for approx. 2 sec
(page 3).
No wireless
connection to
the base, dif-
ferent icons
flash in the
display.
The handset is
outside the range
of the base.
The handset is not
registered.
Move the handset
closer to the base.
Register the handset
(page 2).
!
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Siemens gigaset a24 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Siemens gigaset a24 in the language / languages: English as an attachment in your email.

The manual is 0,4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info