612455
1
Zoom out
Zoom in
Previous page
1/2
Next page
V5075-561-00 09/08
CONNECT radio receiver, flush-mounted, 1-gang switchArt. no. MTN507501© Merten2005V5075-561-0009/08
¼
DANGER
Risk of fatal injury due to electrical current
All work on the device should only be carried out
by trained and skilled electricians. Observe the
country-specific regulations.
½
CAUTION
If you operate devices that do not correspond to
the technical specifications (see technical data),
the connected devices and dimmers may get
damaged.
Connect only one phase (AC 230 V) towards
neutral conductor or functional extra-low volt-
age (FELV) to the make contact.
Do not connect the flush-mounted receiver to
different phases.
In the flush-mounted receiver, the make con-
tact is only separated from the phase by basic
insulation. You must therefore not connect any
safety extra-low voltage (SELV) (safety level
overridden).
The flush-mounted CONNECT radio receiver for the
switch will be referred to in the following as "the flush-
mounted receiver".
The flush-mounted receiver can be used to switch loads
on and off via radio (for information on allowed loads, see
the technical data). When it receives the radio signal, the
flush-mounted receiver switches the corresponding con-
tact.
|
The flush-mounted receiver cannot be used in a
wired two-way circuit.
CONNECT radio receiver, flush-
mounted, 1-gang switch
Operating instructions
Art. no. MTN507501
For your safety
Flush-mounted receiver introduction
en
¼
DANGER
Risk of fatal injury from electric current.
The device has no basic insulation and must
therefore be installed in a way that protects
against accidental contact.
¼
DANGER
Risk of fatal injury from electrical current.
Once a cover A is installed, the distance from
the fixing brackets or screws to the connections of
device B must be at least 4 mm.
If the distance is less than 4 mm, a deeper instal-
lation box must be used.
Also, the fixing brackets or screws of the cover
must not press against the housing.
½
CAUTION
The device can be damaged if not correctly
protected.
The circuit containing the connected loads must
be protected by a fuse with a rating not greater
than 16A.
Simply install the flush-mounted receiver "invisibly" near
the load to be connected, for example in a flush-mounted
socket with a blanking cover.
1 Connecting the flush-mounted receiver.
2 Installing the flush-mounted receiver.
Installing the flush-mounted receiver
B
> 4 mm
A
N
LN
L
10 A
|
Place the antenna as far as possible from metal
parts (connecting cables, retaining rings, etc.) to
avoid interruptions to the radio signal.
|
Metal surfaces in the immediate vicinity (e.g.
flush-mounted metal outlets, metal door frames)
can affect reception.
You can operate the flush-mounted receiver using the
following operating elements:
A taught CONNECT transmitter (e.g. CONNECT radio
push-button/CONNECT sensor surface).
Briefly press switch button B on the device
: this switches the channel.
Only insulated tools may be used for operation on the de-
vice, e.g. an insulated phase tester.
If the flush-mounted receiver is configured with EASY
CONNECT, not all functions/channels can be used. A
description of the EASY CONNECT radio system can be
found in the separate "CONNECT radio system" descrip-
tion, which is supplied with devices with system adminis-
tration (e.g. CONNECT radio push-button).
|
You can analyse and check faults throughout the
radio system with the help of the CONNECT radio
USB data interface (on a suitable PC) and the
CONNECT radio configuration tool.
The device does not react to the taught
transmitter:
Make sure that the maximum range is not exceeded
and that there are no metal surfaces such as metal
cabinets in the radio transmission path.
If necessary, check that the battery is placed correctly
in the radio push-button and that it is not flat.
Make sure that the device is not in programming
mode. (If the LED is flashing, this is the case.)
If necessary, repeat the teaching process.
Operating the flush-mounted receiver
A LED
B Switch button
What should I do if there is a problem?
A
B
NL**
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Schneider Electric MTN507501 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Schneider Electric MTN507501 in the language / languages: English as an attachment in your email.

The manual is 0,13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Schneider Electric MTN507501

Schneider Electric MTN507501 User Manual - German, Dutch, French, Italian - 4 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info