781646

Scheppach DH1200MAX Manual

13
Zoom out
Zoom in
Previous page
1/44
Next page
13GB
plete stop before placing it down. The tool insert can
jam and lead to loss of control over the power tool.
Technical data
Mains voltage: 230V / 50Hz
Power input: 1050W
Idling speed: 480 min-1
Impact rate: 3780 bpm
Drilling capacity
in concrete/stone
(max.):
38 mm
Protection class: II
Weight: 6 kg
Sound and vibration
Sound and vibration values were measured in
accordance with EN 60745.
Sound pressure level Drilling LpA 93,8 dB(A)
Sound pressure level Chisel LpA 95,8 dB(A)
Uncertainty KpA 3 dB
Sound power level Drilling LWA 104,8 dB(A)
Sound power level Chisel LWA 106,8 dB(A)
Uncertainty KWA 3 dB
Wear ear-muffs.
The impact of noise can cause damage to hearing.
Total vibration values (vector sum of three directions)
determined in accordance with EN 60745.
Vibration emission value ah (Handle)
= 14,89 m/s2
Vibration emission value ah (Additional Handle)
= 13,02 m/s2
Uncertainty K = 1,5 m/s2
Additional information for electric power tools
Warning!
The specied vibration value was established in ac-
cordance with a standardized testing method. It may
change according to how the electric equipment is
used and may exceed the specied value in exceptio-
nal circumstances.
The specied vibration value can be used to compare
the equipment with other electric power tools.
The specied vibration value can be used for initial as-
sessment of a harmful effect.
Keep the noise emissions and vibrations to a mi-
nimum.
• Only use appliances which are in perfect working
order.
• Service and clean the appliance regularly.
• Adapt your working style to suit the appliance.
• Do not overload the appliance.
• Have the appliance serviced whenever necessary.
• Switch the appliance off when it is not in use.
• Wear protective gloves.
Residual risks
Even if you use this electric power tool in ac-
cordance with instructions, certain residual risks
cannot be rules out. The following hazards may
arise in connection with the equipment’s construc-
tion and layout:
• Lung damage if no suitable protective dust mask is
used.
• Damage to hearing if no suitable ear protection is
used.
• Health damage caused by hand-arm vibrations if the
equipment is used over a prolonged
Before starting the equipment
Before you connect the equipment to the mains supply
make sure that the data on the rating plate are identi-
cal to the mains data.
Always pull the power plug before making adjustments
to the equipment.
Check the drilling point for concealed electrical cables,
gas and water pipes using a cable/pipe detector.
Additional handle (Fig. 2 – Item 6)
For safety reasons you must only use the hammer drill
with the additional handle.
The additional handle (6) enables you to achieve bet-
ter stability whilst using the hammer drill. The machine
must not be used without the additional handle (6) for
safety reasons.
The additional handle (6) is secured to the hammer
drill by a clamp. Turning the handle anti-clockwise
(looking from the handle) will release the clamp. Tur-
ning the handle clockwise will tighten the clamp. First
release the additional handle clamp. You can then
swing the additional handle (6) into the most comfor-
table working position for you. Now turn the additional
handle in the opposite direction again until the additio-
nal handle is secure.
Tool insertion (Fig. 3)
• Clean the tool before insertion and apply a thin coa-
ting of drill bit grease to the shaft of the tool.
• Pull back and hold the locking sleeve (2).
• Insert the dust-free tool into the tool mounting as far
as it will go whilst turning it. The tool will lock itself.
• Check that it is properly secure by pulling the tool.
… 13 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach DH1200MAX at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach DH1200MAX in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 2.56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info