699892
2
Zoom out
Zoom in
Previous page
1/4
Next page
2 MKP-300 SATEL
- disarm the system (or it’s a keypad with factory settings which has not been used for arming /
disarming).
The LED will remain lit for 15 seconds after pressing the key.
When performing operations on the keypad, the LEDs are used for communication with the user.
2.2 Sound signaling
When performing operations on the keypad, the following sounds are generated:
1 short beep – pressing any numeric key.
2 short beeps – starting function or correct code confirmation.
3 short beeps – command sent confirmation:
arming;
disarming and alarm clearing.
4 short and 1 long beep – command sent confirmation:
output control;
triggering fire or auxiliary (medical) alarm.
2 long beeps – unknown code or function not available.
3. Installation
There is a danger of battery explosion when using a different battery than
recommended by the manufacturer, or handling the battery improperly.
Be particularly careful during installation and replacement of the battery. The
manufacturer is not liable for the consequences of incorrect installation of the battery.
The used batteries must not be discarded, but should be disposed of in accordance
with the existing rules for environment protection.
1. Open the enclosure.
2. Install the battery and register the keypad in the MICRA alarm module (see the manual for MICRA
alarm module).
3. Close the enclosure.
4. Select the place of installation. Check that the transmissions from the keypad placed at that point
reach the MICRA alarm module. In order to send a transmission, close and open the tamper
contact. If the alarm transmission is received, continue with the installation. If the alarm
transmission is not received, select a different mounting location and repeat the test.
5. Open the enclosure.
6. Using wall plugs (screw anchors) and screws, fasten the enclosure base to the wall.
7. Close the enclosure.
4. Codes
The MICRA system can be operated from the keypad after entering the code (only a few functions
can be run without entering the code). The code consists of four digits. Pre-programmed by default in
the keypad is the administrator code: 1234.
Notes:
The factory code should be changed as soon as possible.
The administrator code can not be deleted.
The MICRA module can be preprogrammed by the installer so that entering an invalid code three
times will trigger an alarm.
The administrator code makes it possible to assign individual codes to the people who are to use the
security system. For security reasons, different people should not use the same code.
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel MKP-300 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel MKP-300 in the language / languages: English as an attachment in your email.

The manual is 0,12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel MKP-300

Satel MKP-300 User Manual - German - 4 pages

Satel MKP-300 User Manual - Dutch - 4 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info