783736
17
Zoom out
Zoom in
Previous page
1/18
Next page
angezeigt und blinkt, zu diesem Zeitpunkt werden die
Standardeinstellungen wiederhergestellt.
4. Beim Einstellen der inneren Parameter: Drücken Sie die „SET"-
Taste länger, COP wird angezeigt, die aktuellen Parameter werden
als Werkseinstellungen gespeichert.
5. Funktionsdetails
1. Temperaturregelung
Nach dem Einschalten und die Verzögerungszeit beginnt der
Kompressor bei der Kühlraumtemperatur (eingestellte
Temperatur + Hysterese E3) zu arbeiten und wird bei
Kühlraumtemperatur die eingestellte Temperatur ausgeschaltet.
Kompressor kann nur dann neu gestartet werden, wenn der
Zeitintervall, für den der Kompressor jedes Mal stoppt, länger als
die Verzögerungszeit (Parameter E4) ist.
2. Abtauung durch Ausschalten des Kompressors.
Nach einem Abtauintervall wird automatisch die Abtauung
gestartet. Die Abtauung-LED leuchtet, der Kompressor stoppt.
Wenn die Abtaudauer endet, verlässt der Verdichter den
Abtaubetrieb. Wenn die Kühlraumtemperatur höher ist als
(eingestellte Temperatur + Temperaturhysterese E3), startet der
Kompressor wieder.
Wenn die Abtauintervallzeit auf "00" eingestellt ist, wird die
Funktion der automatischen Abtauung aufgehoben.
3. Anzeige während der Abtauung.
Bei Einstellung des Parameters F4=1 ist die Raumtemperatur
während des Abtauens gesperrt, und der letzte Wert vor dem
Abtauen wird angezeigt. Nach Abtauende wird die normale
Anzeige nach einer Verzögerung von 20 Minuten (oder niedriger
als die eingestellte Temperatur) wieder aufgenommen. Wenn F4
=2, wird „dEF angezeigt.
4. Betriebsmodus des Lüfters
Der Ventilator arbeitet gemäß den Parametern H1, H2.
5. Hoch-, Niedrigtemperatur-Überschreitungsalarm.
Hochtemperatur-Alarm: Nach dem ersten Ausschalten, wenn die
Kühlraumtemperatur höher ist als der Hochtemperaturalarmwert
C1 und die Dauer länger als die Alarmverzögerungszeit (C3) ist,
wird abwechselnd HI und die Kühlraumtemperatur angezeigt.
Wenn die Kühlraumtemperatur niedriger als der
Hochtemperaturalarm C1 ist, wird der Alarm beendet, und die
Anzeige der Kühlraumtemperatur wird wieder aufgenommen.
Niedrigtemperatur-Alarm: Wenn die Kühlraumtemperatur
niedriger ist als der Niedrigtemperatur-Alarmwert C2 und die
Dauer länger als die Alarmverzögerungszeit (C3) ist, wird
abwechselnd L0 und die Kühlraumtemperatur angezeigt. Wenn
die Kühlraumtemperatur höher als der Niedrigtemperatur-
Alarmwert C2 ist, wird der Alarm beendet und die Anzeige der
Kühlraumtemperatur wieder aufgenommen.
Wenn der Alarm eingeschaltet ist, ertönt der Summer, drücken Sie
die beliebige Taste, um den Ton abzustellen.
Alarm für Kondensatorreinigung: Wenn die akkumulierte
Einschaltzeit mehr als P1 beträgt, ertönt der Summer und zeigt
abwechselnd die Kühlraumtemperatur und "Cln" an. In diesem
Fall drücken Sie die beliebige Taste, um den Ton abzubrechen;
nach 2 Minuten wird der Alarm beendet, der akkumulierte Zeit
Wert wird gelöscht und zählt neu, die normale Anzeige wird
wieder aufgenommen. Wenn während des Alarms der Strom
abgeschaltet wird oder der Kühlschrank ausgeschaltet wird, wird
der Alarm beim nächsten Einschalten wieder ausgelöst.
Alarm-Test: Nach Einschalten der Kondensatorreinigungs-
Alarmfunktion, wenn der Strom 10 Sekunden lang ein ist, ▲ und
6 Sekunden lang drücken, die Anzeige blinkt, die zuvor
aufgelaufene Zeit wird gelöscht. Nach 5 Minuten wird
der Alarm wieder ausgelöst.
7. Anormaler Arbeitsmodus
Wenn der Raumfühler kurzgeschlossen oder überhitzt ist (mehr
als 120℃), wird "HH" angezeigt; wenn der Raumfühler offen ist
oder die Temperatur zu niedrig ist (weniger als -45℃), wird
5. Function details
1.
Temperature Control
After turning on for the delay time, the compressor
starts operating when cold-room temperature (set
temperature+ hysteresis E3) and will be off when cold-
room temperature
set temperature.
To protect the compressor, it cannot be re-started unless
the time when the compressor stops every time is longer
than the delay time (Parameter E4 ).
2.
Defrost by turning off compressor
After a defrost interval will automatically enter the defrost
state. The defrost LED is on, the compressor stops. When
defrost duration ends, will exit defrost state. When cold
room temperature is more than (set temp. + temp.
hysteresis E3), the compressor starts.
When the defrost interval time is set to
"
00
"
, the function
of automatic defrost will be cancelled.
3.
Display during defrost
When setting the parameter F4 = 1, the room temp. is
locked during defrost, and the last value before defrost is
displayed. When defrost ends, normal display will be
resumed after 20 minutes delay (or lower than the set
temperature). When F4 =2, dEF will be displayed.
4.
Fan work mode
The fan will work according to H1, H2 parameter.
5.
High, low temperature over limit alarm.
High temperature alarm: After the first time turning off,
when cold room temperature is higher than high
temperature alarm value C1, and duration more than
alarm delay time (C3), will alternate display HI and the
cold room temperature.
When the cold room temperature is lower than high
temperature alarm C1, will exit alarm, and the cold room
temperature will be resumed to be displayed.
Low temperature alarm: When cold room temperature is
lower than low temperature alarm value C2, and duration
more than alarm delay time (C3), will alternate display L0
and cold room temperature. When cold room temperature
is more than low temperature alarm value C2, will exit
alarm and resume cold room temperature display.
When alarm is on, the buzzer sounds, press random button
to cancel the sound.
6. Condenser cleaning alarm: When the accumulated power
on time is more than P 1, the buzzer will sound, alternate
display cold room temperature and “Cln”. In this case, press
random button to cancel the sound, after 2 minutes it will
exit the alarm, the accumulated time will be cleared and will
recount, it will resume normal display. If during alarm power
will be stated off or refrigerator will be shut down, with next
time power on it will keep alarming.
Alarm test: After turning on the condenser cleaning alarm
function, when power is on for 10 seconds, long press and
for 6 seconds, display flashes, the previous accumulated
time will be cleared. After 5 minutes, will
start the alarm.
7.
Abnormal work mode
When the room sensor is short-circuited or overheated
(more than 120
) "HH
"
will be displayed; when the
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Saro GTK1530 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Saro GTK1530 in the language / languages: English, German as an attachment in your email.

The manual is 1.78 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info