783736
16
Zoom out
Zoom in
Previous page
1/18
Next page
7. Manueller Start/Stopp der Abtauung: Drücken Sie die Taste
6 Sekunden lang und Abtauung zu starten oder beenden.
8. Beleuchtung: Taste drücken, die Beleuchtung ist
angeschlossen. Drücken Sie die Taste erneut, dann wird die
Beleuchtung wieder ausgeschaltet.
9. Drücken Sie beim ersten Einschalten einmal die Taste ▼, um
die Verzögerung des Kompressors aufzuheben.
10. Glasscheibenheizung Steuerung: Drücken Sie einmal die Taste
▲, um die Glasscheibenheizung anzuschließen oder abzuschalten.
11. Überprüfen Sie die akkumulierte Betriebszeit für die
Kondensatorreinigung: 6 Sekunden lang drücken, die
akkumulierten Leistung an Betriebstagen wird angezeigt.
12. Einstellung der Parameter
- Drücken Sie die "SET"-Taste und halten Sie sie 6 Sekunden lang
gedrückt, um in den Parametereinstellungsmodus zu gelangen,
während E1 blinkt.
- Drücken Sie erneut die "SET"-Taste, um die Parameter
auszuwählen.
- Drücken Sie die Taste ▲ oder ▼, der Wert des Parameters wird
angezeigt und kann geändert und gespeichert werden.
- Wenn innerhalb von 6 Sekunden keine Taste mehr gedrückt wird,
kehrt das Gerät zum Normalbetrieb zurück.
Para-
meter
Funktion Einstellungs-bereich Standard
E1
Untere
Sollwertgrenze
-45°C ~ eing. Temp. 0 °C
E2
Obere
Sollwertgrenze
Eing. Temp. ~ 45°C +8 °C
E3
Temp. Hysterese
01~20 °C
3 °C
E4
Startverzögerungs-
zeit für Kompressor
0 ~ 10 Min. 3 Min
E5
Offset auf Raum-
temperatur
-10 ~ +10 ° C
-10 ~ +10
°C
F1
Max. Abtauung
Dauer
01 ~ 60 Min. 28 Min
F2
Abtauung Inervall
Zeit
0 ~24 St. 6 St.
F4 Anzeige während
Abtauung
00 = normale Anzeige
01 = letzter Wert bevor
Abtauung
02 = Anzeige dEF”
01
C1
Alarm bei hoher
Temperatur
C2 ~ 45°C 15 °C
C2
Alarm bei niedriger
Temperatur
-45°C ~ C1 -5 °C
C3
Alarm
Verzögerungszeit
0 ~ 90 Min 90 Min
H1
Lüfter Steuerung
00 = parallel mit Kompressor
(Stopp wenn Abtauung)
01 = Dauerbetrieb (Stopp wenn
Abtauung)
02 = parallel mit Kompressor
(Start bei Abtauung)
03 = Dauerbetrieb (Start wenn
Abtauung)
03
H2
Verzögerungszeit des
Lüfters bei
Synchronisierung
0 ~ 120 S 0 S
CF
Temperatur
Einheit
°C = Celsius
°F = Fahrenheit
°C
P1
Kondensator
Reinigung
Alarmzeit
01 ~ 120 Tage
30 Tage
2. Parameter Sperren
Drücken Sie Taste und halten Sie diese 6 Sekunden lang
gedrückt, um die Parameter zu sperren, wenn "LOC" angezeigt
wird, oder um die Sperre aufzuheben, wenn "OP" angezeigt wird.
Parameter können nur angezeigt werden und können nicht
geändert werden, wenn sie gesperrt sind. (Die eingestellte
Temperatureinstellung ist weiterhin aktiv) (Die Werkseinstellung
ist "ON").
3. Wiederaufnahme der Standardeinstellungen: Drücken Sie die
Tasten und gleichzeitig 6 Sekunden lang, "888" wird
button again, the light is disconnected.
9. When first time power on, press button for once to
cancel compressor delay and start the compressor.
10. Defog control: Press button for once, to connect or
disconnect the defog heater.
11. Check the condenser cleaning accumulated time: Long
press ▲ for 6 seconds, flash display the accumulated power
on operation days.
12. Parameter setup
Press “SET” button and hold for 6 seconds to enter the
parameter setup mode while E1 flashes.
Press again SET” button to select the parameters.
Press or button, the value of parameter will be
displayed and can be modified and stored.
If no more button is pressed within 6 seconds, it will return
to normal operation.
Para-
meter
Function Set range Default
E1
Lower set point
limit
-45°C ~ set temp. 0 °C
E2
Higher set point
limit
Set temp. ~ 45°C +8 °C
E3
Temp. hysteresis
01~20 °C
3 °C
E4
Compressor start
delay time
0 ~ 10 min. 3 min
E5
Offset on room
temperature
-10 ~ +10 ° C
-10 ~ +10
°C
F1
Max. defrost
duration
01 ~ 60 min. 28 min
F2
Defrost interval
time
0 ~24 hr. 6 hr.
F4 Display during
defrost
00 = normal display
01 = last value before
defrost
02 = display dEF”
01
C1
High temperature
alarm
C2 ~ 45°C 15 °C
C2
Low temperature
alarm
-45°C ~ C1 -5 °C
C3
Alarm delay time
0 ~ 90 min
90 min
H1
Fan control
00 = parallel with
comp. (stop when
defrost)
01 = continuous
running (stop when
defrost)
02 = parallel with
comp. (start when
defrost)
03 = keep running
(start when defrost)
03
H2
Fan retardant time
when synchronized
0 ~ 120 s 0 s
CF Temperature unit
°C = Celsius
°F = Fahrenheit
°C
P1
Condenser
cleaning alarm
time
01 ~ 120 days
30 days
Parameters Locking
Pressbutton and hold for 6 seconds to lock the
parameters if "LOC" is displayed, or to unlock if
"
OP
"
is displayed. Parameters can be displayed only and
cannot be modified if locked. (The set temperature
adjustment is still active) (The factory default is
"
ON
"
).
The factory default resumption: press button and
button simultaneously for 6 seconds,
"
888
"
is
displayed and flashes, at this time will resume to
factory defaults.
When adjusting the inner parameters, long press
“SET button, COP will be displayed, the current
parameters will be saved as factory defaults.
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Saro GTK1530 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Saro GTK1530 in the language / languages: English, German as an attachment in your email.

The manual is 1.78 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info