705954

Russell Hobbs 24440-56 Manual

5
Zoom out
Zoom in
Previous page
1/96
Next page
5
DRY IRONING
You can dry iron by just not pressing the steam button, but if you want to make sure you don’t press it
accidentally, then you should iron with an empty reservoir. You can do your dry ironing rst, then switch
o, ll the reservoir and do your steam ironing.
VERTICAL STEAMING
Remove wrinkles from hanging clothes, hanging curtains, and furnishing fabrics.
• Check that there’s adequate ventilation behind the fabric otherwise moisture may build up causing
mildew.
• Check that there’s nothing behind the fabric that may be damaged by the steam.
• Check that pockets, turn-ups, and cus are empty.
1. Set the temperature control to max.
2. Hold the iron close to (but not touching) the fabric.
We recommend using the steam button to produce steam for smaller areas, as it gives you better control.
AFTER USE
1. Put the iron on top of the base unit and turn the temperature control to •.
2. Set the on/o sw itch to O and unplug the base unit.
3. Empty the reservoir.
4. Let the iron cool down completely before cleaning it, moving it, or storing it away.
5. The steam pipe can be coiled together and placed into the hose clip.
6. Wrap the mains cable around the steam generator in an anti-clockwise direction then slot the plug
into the socket (Fig C).
7. The water reservoir must be emptied when storing your steam station vertically.
CARE AND MAINTENANCE
1. Unplug the base unit, and let the appliance cool down fully.
2. Wipe outer surfaces with a damp cloth.
3. Remove spots from the soleplate with a little vinegar.
4. Take care not to scratch the soleplate.
ANTISCALE CARTRIDGE
To extend the life of the appliance and to avoid problems with lime scale, your steam generator is tted
with an anti-scale cartridge. The life of the anti-scale cartridge depends on the frequency of use and the
hardness of the water in your area. In a soft water area this should be about 100 uses. Do not put any
descaling products (including vinegar) into the reservoir. This can damage the appliance.
To replace the cartridge:
1. Switch o and unplug your steam generator.
2. Allow your steam generator to cool down for at least 1 hour until the soleplate is cold.
3. Remove the reservoir from the front of the unit.
4. Pull the anti -scale cartridge vertically out of the reservoir. Note that the cartridge may contain water
when it is removed (Fig A).
5. Fit the new cartridge and push it down rmly into the reservoir.
6. Rell and ret the reservoir.
7. Plug in your steam generator.
8. Once the appliance is ready, pull the steam trigger until the steam is being produced. This will prime
the system.
Important: Using the appliance without changing the cartridge can cause a reduction in the generated
steam output and damage the appliance. The guarantee will not cover damage caused to the appliance
by not changing the anti- scale cartridge when required.
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Russell Hobbs 24440-56 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Russell Hobbs 24440-56 in the language / languages: All languages as an attachment in your email.

The manual is 1,42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info