565648
4
Zoom out
Zoom in
Previous page
1/16
Next page
MONTAGE 1
Die Kette gut geordnet
vor das Rad legen.
Das farbige Ringende
hinter das Antriebsrad
herumführen. Beide
Ringenden erfassen
und auf die Reifen-
lauffläche hochziehen.
FITTING 1
Arrange the snow chain
neatly in front of the wheel.
Lead the coloured end
piece aroundbehind the
driven wheel. Fasten both
ring ends and place high
on the tyre tread.
MONTAGE 2
Verschlußteile (wie
Bildausschnitt) einhän-
gen und geschlossenen
Seilring auf die Reifen-
lauffläche legen.
MONTAGE 3
Das Endglied der
Außenkette in den farbi-
gen Haken einhängen.
Seilring über die
Lauffläche schieben bis
der Seilring in der Mitte
der Reifenflanke zu
liegen kommt
(wie Bildausschnitt).
MONTAGE 5
Wenn der Abstand
des Stahlseils an
der Ratsche nach
dem Spannen
weniger als 2cm
beträgt, Kette an
oberem Ver-
schlusshaken
zurückhängen.
FITTING 2
Couple the locking parts
(as shown in the diagram)
and place the closed wire
ring on the tyre tread.
FITTING 3
Engage the end link of the
outer chain in the coloured
hook. Push the wire ring
over the tread (picture
shows partial completion)...
until the wire ring lies in
the middle of the tyre flank
(as shown in the close up).
FITTING 5
If after tensioning the
length of the cable is
less than 2 cm, than
hang the chain at the
upper locking hook
one link shorter.
FITTING 4
Hold the lower tensioning device
and raise the lever from the tensio-
ning device casing until it clicks into
place (OPEN position). Grasp the
tensioning device and completely
extract the cable, which is thus
ready to be hooked up.
Attach the end fitting of the rope
to the flat hook. Grasp the tensio
-
ning device located in the bottom
and push the lever until it clicks
into position (GO position):in this
way the cable will automatically
self-tighten.
MONTAGE 4
Spannvorrichtung unten greifen und
Hebel vom Gehäuse der Spann-
vorrichtung anheben, bis der End-
anschlag hörbar einrastet (Position
OPEN). Spannvorrichtung greifen
und Stahlseil vollständig herauszie
-
hen, das dann eingehängt werden
kann. Das Ende des Stahlseils in
den farbigen Haken einhaken. Die
unten montierte Spann-vorrichtung
greifen und den Hebel drücken, bis
der ndanschlag hörbar einrastet
(Position GO). Auf diese Weise wird
das Stahlseil automatisch gespannt.
Danach langsam anfahren. Ein
Nachspannen ist nicht erforderlich.
4
DE
EN
MONTAGE
ACHTUNG: Betätigen Sie die automatische Spann-
vorrichtung erst nachdem Sie das farbige Seilendstück
der Spannvorrichtung eingehakt haben, wie es in der
Abbildung zu sehen ist.
WARNING: Set the automatic tensioning device in action
only after having connected the orange plastic hook as
shown in the picture.
<2cm
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for RUD Star Track automatic RUDcompact at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of RUD Star Track automatic RUDcompact in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 1,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info