Manual Rossmax SB100 (page 1 of 2) (English)

783666

Zoom out

Zoom in

1/2

Cleaning

Maintenance

Troubleshooting

Specification

1. Please clean the surface of the device before using.

Wipe the device with medical alcohol (70% isopro-

pyl alcohol)first, and then let it dry in air or clean it

by dry clean fabric. When cleaning the device with

water, the water temperature should be lower than

60°C

2. Using the medical alcohol to disinfect the product

after use, prevent from cross infection for next time

use.

3. The best storage environment of the device is - 25°C

to 70°C ambient temperature and not higher than

90% relative humidity.

Note: 1. Do not sterilize, autoclave or immerse this de-

vice in liquid. Do not pour or spray any liquids

onto the device.

2. Do not use caustic or abrasive cleaning

agents, or any cleaning agent containing am-

monium chloride or isopropyl alcohol.

Recommends user to return this device to the man-

ufacturer perform the following checks every 24

months.

- Inspect the equipment for mechanical and function-

al damage or deterioration.

- Ensure all user interface keys and accessories func-

tion normally.

Note: Manufacturer use simulator of model Index 2

to verify operation of the pulse oximeter equip-

ment.

Symptoms Check points Corrections

SpO2 or

pulse rate

cannot

displayed

Applied nger

improperly.

Place the nger prop-

erly and try again.

SpO2 is too low to

detect

Try again; go to con-

sult with your physi-

cian if you are sure the

device works well.

SpO2 or

pulse rate are

not displayed

stably

Applied nger

improperly.

Place the nger prop-

erly and try again.

Finger is shaking

or body is moving. keep body steady

No display

when button

is pressed

Batteries run

down

Replace with new

batteries

Batteries not

inserted correctly. Re-insert batteries

The display

disappears

suddenly

The device will

auto power o

when it gets no

signal.

Normal

Low battery Replace with new

batteries

Note: If the unit does not work, return it to your

dealer. Under no circumstance should you

disassemble and repair the unit by yourself.

SpO2

Measuring

range

35%~99%, (the resolution is 1%).

Accuracy 70%~99%: ±2%, Below 35~69%:

unspecied.

Optical Sensor The wavelength of red LED is 660 nm

and Infrared LED is 905/880 nm with

maximum optical output power of 4

mW/sr.

Pulse

Measuring

range

30 bpm~250 bpm (the resolution is 1

bpm)

Accuracy ±3 bpm

Power source AAA × 2 (Alkaline)

Battery life Continually for 16 hours with two alkaline

batteries

Operating

Condition

Temperature: 5°C~40°C (41°F ~ 104°F),

Relative Humidity: 15-95% (non

condensing), Atmospheric pressure:

700hPa ~ 1060hPa, Attitude: -1,280 to

12,000 feet (-390m to 3,658m)

Storage /

Transportation

Condition

Temperature: -25°C~+70°C(-13°F ~

158°F), Relative humidity: 15-90%(non

condensing), Atmospheric pressure:

700hPa ~ 1060hPa, Attitude: -1,280 to

12,000 feet (-390m to 3,658m), The time

from 70°C or -25°C back to use : 3 hours

Dimensions 63.5(L) × 34W) × 35(H) mm

Weight About 37g (without the batteries)

Standards IEC60601-1-2, Class B, IEC60601-1, Type BF,

ISO80601-2-61, IEC/EN60601-1-11

Type BF applied parts

IP Classication IP22: Protection against harmful ingress of

water and particulate matter

Note:

- A description of the effect on displayed and transmit-

ted SpO2 and pulse rate:

- Data averaging: 4 seconds for SpO2; 8 seconds for

pulse rate.

- Data update delay: Less than 2 seconds.

be evaluated at the measurement site. Rather, they

are exclusively used to display the current signal vari-

ation at the measurement site and do not enable re-

liable diagnostics for the pulse.

- A warning that other cables and accessories may

negatively aect EMC performance.

- A warning regarding stacking and location close to

other equipment.

- A warning that use of other accessories results in

non-compliance.

- The maximum temperature of sensors which the

user will touch might reach 42°C when operating in

the 40°C environment.

- The safety way for all people use is measuring for 10

minutes, and turn it o for 20 minutes before meas-

ure again.

- The oximeter is calibrated in the factory before sale,

there is no need to calibrate it during its life cycle.

Model: SB100

www.rossmax.com

Fingertip Pulse Oximeter

Rossmax InnoTek Corp.

12F., No. 189, Kang Chien Rd., Taipei,

114, Taiwan.

CMC Medical Devices & Drugs S.L.

C/ Horacio Lengo Nº 18, CP 29006,

Málaga, Spain

WARNING: The symbol on this product means that it's an electronic product

and following the European directive 2012/19/EU the electronic products have

to be dispose on your local recycling centre for safe treatment.

EMC guidance and manufacturer’s declaration

Recommended separation distances between portable and mobile RF communications equipment and the ME equipment

The Finger-tip pulse oximeter is intended for use in an electromagnetic environment in which radiated RF disturbances are con-

trolled. The customer or the user of the Finger-tip pulse oximeter can help prevent electromagnetic interference by maintaining a

minimum distance between portable and mobile RF communications equipment (transmitters) and the Finger-tip pulse oximeter

as recommended below, according to the maximum output power of the communications equipment.

Rated maximum output

power of transmitter / W

Separation distance according to frequency of transmitter / m

150 kHz to 80 MHz , d=[3.5/

V1]√P 80 MHz to 800 MHz , d=[3.5/

E1]√P 800 MHz to 2,5 GHz , d=[7/

E1]√P

0.01 0.1 0.1 0.2

0.1 0.4 0.4 0.7

11.2 1.2 2.3

10 3.7 3.7 7.4

100 11.7 11.7 23.3

Declaration – electromagnetic emissions

The Finger-tip pulse oximeter is intended for use in the electromagnetic environment specied below. The customer or the user of

the Finger-tip pulse oximeter should assure that it is used in such an environment.

Emissions test Compliance Electromagnetic environment - guidance

RF emissions CISPR 11 Group 1 Portable and mobile RF communications equipment should be used no

closer to any part of the EQUIPMENT or SYSTEM including cables, than the

recommended separation distance calculated from the equation applicable

to the frequency of the transmitter. Interference may occur in the vicinity of

equipment marked with the following symbol.

RF emissions CISPR 11 Class B The Finger-tip pulse oximeter is suitable for use in all establishments,

including domestic establishments and those directly connected to the

public low-voltage power supply network that supplies buildings used

for domestic purposes.

Harmonic emissions IEC 61000-3-2 N/A

Voltage uctuations/Flicker emissions

IEC 61000-3-3 N/A

Declaration – electromagnetic emissions and immunity – for EQUIPMENT and SYSTEMS that are use in the professional health-

care facility environment or in the home healthcare environment

The Finger-tip pulse oximeter declaration – electromagnetic immunity

The Finger-tip pulse oximeter system is intended for use in the electromagnetic environment specied below. The customer or

the user of the Finger-tip pulse oximeter system should assure that it is used in such an environment.

Immunity test IEC 60601 test level Compliance level Electromagnetic environment - guidance

Conducted RF IEC

61000-4-6 3 Vrms ; 6 Vrms ; 150

kHz to 80 MHz N/A Portable and mobile RF communications equipment

should be used no closer to any part of the EQUIPMENT

or SYSTEM including cables, than the recommended

separation distance calculated from the equation ap-

plicable to the frequency of the transmitter. Interference

may occur in the vicinity of equipment marked with the

following symbol.

Radiated RF IEC

61000-4-3 3 V/m ; 10V/m ; 80

MHz – 2.7 GHz l 80% 3 V/m ; 10V/m ; 80

MHz – 2.7 GHz ; 80%

Proximity elds

from RF wireless

Communications

equipment IEC

61000-4-3

27 V/m 385 MHz 27 V/m 385 MHz

28 V/m 450 MHz 28 V/m 450 MHz

9 V/m 710 MHz 9 V/m 710 MHz

745 MHz 745 MHz

780 MHz 780 MHz

28 V/m 810 MHz 28 V/m 810 MHz

870 MHz 870 MHz

930 MHz 930 MHz

28 V/m 1720 MHz 28 V/m 1720 MHz

1845 MHz 1845 MHz

1970 MHz 1970 MHz

28 V/m 2450 MHz 28 V/m 2450 MHz

9 V/m 5240 MHz 9 V/m 5240 MHz

5500 MHz 5500 MHz

5785 MHz 5785 MHz

Declaration – electromagnetic immunity

The Finger-tip pulse oximeter system is intended for use in the electromagnetic environment specied below. The customer or

the user of the Finger-tip pulse oximeter system should assure that it is used in such an environment.

Immunity test IEC 60601 test level Compliance level Electromagnetic environment - guidance

Electrostatic discharge

(ESD) IEC 61000-4-2 ±8 kV contact

±2 kV, ±4 kV, ±8 kV,

±15 kV air

±8 kV contact

±2 kV, ±4 kV, ±8

kV, ±15 kV air

Floors should be wood, concrete or ceramic tile.

If oors are covered with synthetic material, the

relative humidity should be at least 30 %.

Electrical fast transient/

burst IEC 61000-4-4 ±2 kV for power supply lines

±1 kV for input/output lines N/A Mains power quality should be that of a typical

commercial or hospital environment.

Surge IEC 61000-4-5 ±0.5 kV

±1 kV dierential mode

±2 kV common mode

N/A Mains power quality should be that of a typical

commercial or hospital environment.

Voltage dips, short

interruptions and voltage

variations on power

supply input lines IEC

61000-4-11

0 % UT; 0, 5 cycle At 0°, 45°,

90°, 135°, 180°, 225°, 270°

and 315°

0 % UT; 1 cycle And 70

% UT; 25/30 cycle Single

phase: at 0°

N/A Mains power quality should be that of a typical

commercial or hospital environment. If the user

of the EQUIPMENT or SYSTEM requires continued

operation during power mains interruptions, it is

recommended that the EQUIPMENT or SYSTEM

be powered from an uninterruptible power sup-

ply or a battery.

Power frequency (50/60

Hz) magnetic eld IEC

61000-4-8

30 A/m 30 A/m Power frequency magnetic elds should be at

levels characteristic of a typical location in a typi-

cal commercial or hospital environment.

IN0SB100000000252

Warranty Card

This instrument is covered by a 2 year guarantee from the date of purchase, batteries

and accessories are not included. The guarantee is valid only on presentation of the

guarantee card completed by the dealer confirming date of purchase or the receipt.

Opening or altering the instrument invalidates the guarantee. The guarantee does

not cover damage, accidents or non-compliance with the instruction manual. Please

contact your local seller/dealer or www.rossmax.com.

Customer Name: __________________________________

Address: _______________________________________

Telephone: _____________________________________

E-mail address: ___________________________________

Product Information: ______________________________

Date of purchase: _________________________________

Store where purchased:

______________________________________________

RI_IB_SB100_EN_

2Yr_TP_ver2004

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Rossmax SB100 in the language / languages: English as an attachment in your email.

The manual is 1.96 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Rossmax SB100

Rossmax SB100 User Manual - German - 2 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Rossmax SB100 Manual

Product: