Manual Rockford Fosgate t 1001 bd (page 6 of 52) (English, German, French, Italian, Spanish)

167797

Zoom out

Zoom in

1/52

INSTALLATION

Passenger Compartment Mounting

Mounting the amplifier in the passenger compartment will work as long as you provide a sufficient amount

of air for the amplifier to cool itself. If you are going to mount the amplifier under the seat of the vehicle,

you must have at least 1" (2.54cm) of air gap around the amplifier's heatsink.

Mounting the amplifier with less than 1" (2.54cm) of air gap around the amplifier's heatsink in the

passenger compartment will not provide proper cooling and will severely affect the performance of the

amplifier and is strongly not recommended.

BATTERY AND CHARGING

Amplifiers will put an increased load on the vehicle's battery and charging system.We recommend

checking your alternator and battery condition to ensure that the electrical system has enough capacity to

handle the increased load of your stereo system. Stock electrical systems which are in good condition

should be able to handle the extra load of any Power Series amplifier without problems, although battery

and alternator life can be reduced slightly.To maximize the performance of your amplifier,we suggest the

use of a heavy duty battery and an energy storage capacitor.

WIRING THE SYSTEM

CAUTION:If you do not feel comfortable with wiring your new unit, please see your

local Authorized Rockford Fosgate Dealer for installation.

CAUTION:Before installation, disconnect the battery negative (-) terminal to prevent

damage to the unit, fire and/or possible injury.

CAUTION:Avoid running power wires near the low level input cables, antenna, power

leads, sensitive equipment or harnesses.The power wires carry substantial

current and could induce noise into the audio system.

1. Plan the wire routing. Keep RCA cables close together but isolated from the amplifier's power cables

and any high power auto accessories, especially electric motors.This is done to prevent coupling the

noise from radiated electrical fields into the audio signal.When feeding the wires through the firewall

or any metal barrier,protect them with plastic or rubber grommets to prevent short circuits. Leave

the wires long at this point to adjust for a precise fit at a later time.

NOTE:We recommend a 4 AWG wire for use on the power (B+) and ground (GND) connections.

2. Prepare the RED wire (power cable) for attachment to the amplifier by stripping 5/8" of insulation

from the end of the wire. Insert the bared wire into the B+ terminal and tighten the set screw to

secure the cable in place.

NOTE:The B+ cable MUST be fused 18" or less from the vehicle's battery. Install the fuseholder under

the hood and ensure connections are water tight.

3. Trim the RED wire (power cable) within 18" of the battery and splice in a inline fuse holder (not

supplied). See Specifications for the rating of the fuse to be used.

DO NOT install the fuse at

this time.

4. Strip 1/2" from the battery end of the power cable and

crimp a large ring terminal to the cable. Use the ring terminal

to connect to the battery positive terminal.

5. Prepare the BLACK wire (Ground cable) for attachment to

the amplifier by stripping 5/8" of insulation from the end of

the wire. Insert the bare wire into the GROUND terminal

and tighten the set screw to secure the cable in place.

epar

e the chassis gr

ound b

y scraping any paint from the

metal surface and thor

oughl

y clean the ar

ea of all dir

t and

ease

Strip the other end of the wir

e and attach a ring

connector

Fasten the cable to the chassis using a

non-anodized scr

w and a star washer

NOTE:Keep the length of the BLACK wire (Ground) as short as

possible

Always less than 30"(76.2cm).

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Rockford Fosgate t 1001 bd in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 1,87 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Rockford Fosgate t 1001 bd Manual

Product: