167797
4
Zoom out
Zoom in
Previous page
1/52
Next page
T500-1bd
CP
T1500-1bd CP
T1000-1bd CP
45678
9 10 12
11 13 14
4578
96 10 12
961012
11 13 14
4 5 7 8 11 13 14
1. Power LED (Top of unit - Not Shown) This Blue LED illuminates when the unit is turned on.
2. Thermal LED (Top of unit - Not Shown) This Red LED illuminates if the amplifier internal components
become too hot and engage the thermal protection.The amplifier will shut down to cool if this occurs.
3. Protect LED (Top of unit - Not Shown) This Yellow LED illuminates if a short circuit or too low of an
impedance is detected at the speaker connections.The amplifier will automatically shut down if this occurs.
4. Cast Aluminum Heatsink The cast aluminum heatsink of the Power amplifier dissipates heat generated by
the amplifier's circuitry.
5. Speaker Terminals The heavy duty,nickel-plated clamp wire connectors (
+
and -) will accept wire sizes from
8 AWG to 18 AWG.
6. Remote Punch EQ (Optional Controller) The Remote Punch EQ connection is made with a RJ-45 cable
and can be installed in a variety of ways for easy control access.The control is used to boost low and/or high
frequency information to overcome road noise.The remote overrides the Punch EQ on the amplifier when
connected.
NOTE: Previous (prior to 2007) Punch Bass and Para-Punch remotes will not work with these amplifiers.
7.
Punch EQ This control is a narrow band adjustment variable from 0dB to +18dB @ 45Hz with a Gyrator
based Punch EQ that eliminates frequency shift with boost.
8.
Infrasonic Filter A 28Hz High Pass filter designed to prevent frequencies below the audio range from being
applied to the subwoofer from the amplifier. Consequently improving subwoofer performance and power
handling,particularly in vented enclosures.
9.
Variable Crossover – Is a built-in 24dB/octave Butterworth filter with a crossover point variable from 35Hz to
250Hz.The crossover is set to Low-Pass (LP).
10.
Gain Control The input gain control is preset to match the output of most source units.It can be adjusted to
match output levels from a variety of source units.
11.
RCA Pass-Thru Jacks This Pass-Thru provides a convenient source for daisy-chaining an additional amplifier
without running an extra set of RCA cables from the front of the vehicle to the rear amplifier location.
12. RCA Input Jacks The industry standard RCA jacks provide an easy connection for signal level input.They are
nickel-plated to resist the signal degradation caused by corrosion.
13. REM
T
erminal
The hea
vy duty
,
nickel-plated captive c-clamp wire connector will accept wire sizes from
12
A
WG to 24
A
WG.This terminal is used to remotely turn-on and turn-off the amplifier when +12V DC is
a
pplied.
14.
Power Terminals The power and ground are nickel-plated captive c-clamp wire connectors and will
accommodate up to 4 AWG wire.
4
DESIGN FEATURES
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Rockford Fosgate t 1001 bd at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Rockford Fosgate t 1001 bd in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 1,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info