629008
2
Zoom out
Zoom in
Previous page
1/2
Next page
WI-FI SETUP
Download the Ring app from the App Store
Google Play or Windows Store. Open the
Ring app and select Setup Device. Follow
the in-app instructions to set up your Ring.
You will need your network information
(SSID and password) to complete your
Ring setup.
INSTALLATION
1. Remove doorbell button and power off your
transformer (for wired installation only).
2. Line up the mounting bracket using the provided
mounting level.
4. Install the mounting bracket using the provided
screwdriver bit, handle and drill bit.
Brick - use provided screws and anchors
Concrete - use provided screws and anchors
Stucco - use provided screws and anchors
Wood - use provided screws
Vinyl - use provided screws
5. Remove the mounting level.
6. Connect your doorbell wiring to the terminal screws
located on the mounting bracket
(for wired installation only).
7. Place the device on the mounting bracket.
8. Tighten the security screws at the bottom of the device
using the proprietary screwdriver bit. Please do not
over-tighten the security screws.
9. Provide power back to your transformer
(for wired installation only).
HARDWIRING REQUIREMENTS
If powering off doorbell wiring, the wiring
must be connected to a transformer and a
doorbell with a voltage of 8VAC - 24VAC to
ring your doorbell chime.
BATTERY CHARGING
Charge your device using a USB-compatible wall charger
or laptop. To ensure your device is fully charged, charge
the device prior to Wi-Fi setup and installation.
LED RING LIGHTING SEQUENCES
Battery Charging
Battery Charging
Complete
Call Initiated
Call Connected
Hardwired
Setup Mode
Software Update
Factory Reset
LED Ring
spins blue.
LED Ring stays
fully lit blue.
LED Ring spins
blue, then white.
LED Ring stays
fully lit blue.
LED Ring
spins white.
LED Ring
blinks white.
LED Ring
blinks blue.
ANSWERING A CALL
Mute Volume
Disable Microphone
End Call
Call Zoom
To disable notications for your Ring device,
select it from “My Devices. Select “Device
Settings” and toggle notications off.
6 7 8 9
If your chime is electronic (e.g. plays a melody), you
may need to install a diode, which is commonly found
inside your current doorbell button, or check with your
doorbell manufacturer.
Connect the diode to the terminals with the arrow
on the diode facing towards the doorbell chime as
shown below.
LED Ring stays
dimly lit white.
For additional product information and
helpful tips, check out our support
forum at:
http://ring.com/help
For immediate assistance,
please call us at:
DOMESTIC: 1-800-656-1918
INTERNATIONAL: +1 310-929-7085
7 days a week
CUSTOMER SUPPORT
1523 26th St.
Santa Monica, CA 90404
10
Protect the device from direct sunlight. Install the device at dry locations and protect it
against rain and humidity. The device may not get contact to salt water or other
conductive liquids. The device must be charged only within a building in a dry state.
Hereby, Bot Home Automation, declares that this consumer
electronic is in compliance with the essential requirements
and other relevant provisions of Directive 1999/5/EC. The
declaration of conformity may be consulted at
www.ring.com/DoC.pdf.
AT&T
11:56 AM
END CALL
Front
Transformer
Rear
TransformerElectronic
Chime
AC
IN
Diode
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ring Video Deurbel at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ring Video Deurbel in the language / languages: English as an attachment in your email.

The manual is 5,5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Ring Video Deurbel

Ring Video Deurbel Installation Guide - English - 2 pages

Ring Video Deurbel User Manual - English - 20 pages

Ring Video Deurbel User Manual - Dutch - 15 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info