629008
1
Zoom out
Zoom in
Previous page
1/2
Next page
MAC ID: XXXXXXXXXXX
S/N: XXXXXXXXXXX
Product name: Ring
FCC ID: YOPGS1011MEE
Model name: Video Doorbell
Power input: 8-24 VAC, 5Vdc 1 A
VIDEO DOORBELL
Setup and
Installation Guide
Step 1
Download the Ring app
The Ring app will walk you through
the process outlined in this manual,
but in case you like reading small
print we’ve also included this manual.
Visit: ring.com/app
Visit the online setup guide for
extra help
We have an online guide with videos
and tutorials all about setting up and
using your Ring Video Doorbell.
Visit: ring.com/setup
Step 2
Say “Hello” to the back of your Ring
Doorbell
Setup Button – The orange button is
the setup button. You’ll be instructed
to push it during the in-app setup.
Charging Port – If you’re not wiring
your Ring Doorbell, you’ll need to
charge it periodically by plugging
the provided orange cable into the
charging port.
For more, visit: ring.com/charging
Setup Button Charging Port
Step 3
Perform the in-app setup
The Ring app will walk you through
this process.
Download the Ring app by visiting
ring.com/app
Select the plus sign in the Ring app
to set up a new device, and when
prompted, select Video Doorbell.
Perform setup inside near
your router. You’ll need your
network name and Wi-Fi password.
Step 4
Push the Front Button to Run a Test
After setup, push the front button on
your Ring Doorbell indoors near your
router to see video from your Ring
Doorbell in the Ring app. Then test
your Ring Doorbell outside.
If video quality from your
Ring Doorbell is not as good
outdoors as it was indoors, you may
need to move your router closer to
your door, or invest in an extender.
Learn more at: ring.com/extender
If you notice a diode when you
remove your wired doorbell,
take note of this as it means you will
need to use the included diode.
Step 5
Remove Your Existing
Doorbell (optional)
If you’re replacing a wired doorbell,
first turn off the power at the breaker.
Then remove your doorbell from the
wall, and disconnect the wires.
Diode
Step 6
Install the Mounting Bracket
Take everything that came in the
box, along with a power drill if
you’re installing on stucco, brick or
concrete, to the spot where you’ll be
installing your Ring Doorbell.
Snap the provided level onto the
mounting bracket and use it to
help position the bracket.
Then remove the orange tape, and
use the mounting bracket as a
template to mark the four
corner holes.
Mounting
bracket
On wood or siding, you can skip this
part, and screw the bracket directly
into your wall.
If you have a smaller drill bit, it
may help to use this bit to drill
pilot holes.
Installing the Mounting Bracket
(continued)
On stucco, brick, or concrete install
the anchors using the provided drill
bit and a power drill before installing
the mounting bracket.
Installing the Mounting Bracket
(continued)
Use the phillips head side of the Ring
screwdriver for screwing in your
mounting bracket.
Installing the Mounting Bracket
(continued)
Drive the screws into the anchors, or
directly into your wall until they are
flush with the mounting
bracket, and the bracket is
flat against your wall.
If your wall is not
completely flat,
be careful not to screw the
bracket in so tightly that it bends.
2 3 4 5 6 7 8 9 10
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ring Video Deurbel at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ring Video Deurbel in the language / languages: English as an attachment in your email.

The manual is 16,74 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Ring Video Deurbel

Ring Video Deurbel Quick start guide - English - 2 pages

Ring Video Deurbel User Manual - English - 20 pages

Ring Video Deurbel User Manual - Dutch - 15 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info