Manual Renkforce RS2W (page 3 of 8) (English, German, Dutch, French)

657053

Zoom out

Zoom in

1/8

b) Operating location

• The product may be used in dry, enclosed indoor areas only; it must not get damp or

wet.

• Only use the product when it is securely installed and steady. Install the product, e.g.

in a suitable ﬂush or wall-mounted box or other suitable housing, so that the required

protection against contact is ensured.

• The product must not be exposed to extreme temperatures, strong vibrations or

heavy mechanical stress. Keep the product out of strong magnetic ﬁelds that occur

near machines, electric motors or loudspeakers.

• Do not operate the device in environments where there are high levels of dust, ﬂam-

mable gases, vapours or solvents. There is a danger of ﬁre and explosion!

• Do not use this product in hospitals or medical institutions. Although RS2W radio

system transmitters only emit relatively weak radio signals, these may lead to the

malfunctioning of life-support systems. The same may also apply to other zones.

c) Connection, handling and use

• Never touch or handle the product with damp or wet hands. There is a risk of a life-

threatening electric shock!

• Only carry out the installation when all the mains cables to the wireless switch are

disconnected from the mains voltage. Otherwise, there is a risk of a life-threatening

electric shock!

• An all-pole disconnection from the mains voltage (such as a surge protector) must

be provided as part of the wiring set-up.

• Never connect the product to the power supply immediately after it has been trans-

ferred from a cold room into a warm one (e.g., during transport). Condensation water

that forms might destroy the device. Moreover, there is danger of electric shock!

Allow the device to reach room temperature before switching it on. Wait until the

condensation has evaporated. This might take several hours. Only after this should it

be plugged in to the mains supply and put into use.

• Never overload the product. Observe the maximum connected load allowed in the

“Technical Data” chapter.

• Do not use the product if it is damaged. There is a risk of a life-threatening electric

shock! In this case, dispose of the product in an environmentally correct manner.

• If it can be assumed that safe operation is no longer possible, the device must be

turned off and precautions must be taken to ensure that it is not used unintentionally.

Do not touch the wireless switch or any device connected to it.

Disconnect the wireless switch from the mains by switching off at the appropriate

circuit breaker or by pulling out the fuse. Furthermore, turn off the earth leakage

circuit breaker to disconnect all the poles of the mains supply.

Safe operation can no longer be assumed if:

- the product shows visible signs of damage

- the product does not work at all or works poorly (leaking smoke or a smell of

burning, audible cracking noises, discolouration to the product or the adjacent

surfaces)

- the product was stored under unfavourable conditions

- it was exposed to heavy loads during transport

• Use the product only in a temperate climate, never in a tropical climate.

• If you have any questions that are not answered in these operating instructions,

please contact our technical department or another specialist.

Preparations for installation

Please observe the chapter “Safety instructions”!

• To use, install the wireless switch in a suitable ﬂush or wall-mounted box or other suitable hous-

ing.

• The wireless switch must be disconnected from the power supply during installation. First,

switch off all poles of the mains supply by switching off at the associated circuit breaker or

removing the fuse and then also switch off the associated RCD (residual current device).

Secure it against unauthorised reconnection, e.g., with a danger sign. Check the mains connec-

tion for absence of voltage using a suitable tester.

Operating instructions

RS2W Wireless switch micro

Item no. 1243793

Intended use

The wireless switch is intended for wireless switching on and off connected devices using suitable

radio transmitter of the R2SW system.

The wireless switch may only be used on mains voltage (230 V/AC, 50 Hz). A maximum consumer

load of 3500 W/15,2 A (resistive load) or 600 W/2,6 A (inductive load) can be connected.

Please read the operating instructions carefully and do not discard them. If you pass the product

on to a third party, please hand over these operating instructions as well.

Any use other than that described above could lead to damage to this product and involves the risk

of short circuits, ﬁre, electric shock, etc. No part of the product may be modiﬁed or converted! The

safety instructions must be observed at all times.

This product complies with the applicable national and European requirements. All names of com-

Package contents

• Wireless switch

• Operating instructions

Explanation of symbols, inscriptions

The lightning symbol inside a triangle is a warning to inform you of potential risks of

your health and life, such as electrical shock.

This symbol indicates speciﬁc risks associated with handling, function and use.

The “arrow” symbol indicates special tips and operating information.

The product is only intended to be installed and used in dry, indoor rooms; it must not

get damp or wet.

Observe the operating instructions!

Safety instructions

Read the complete operating manual carefully before using the product as it contains

important information about the correct installation and operation.

Damage due to failure to follow these operating instructions will void the warranty!

We do not assume any liability for any resulting damage!

We do not assume any liability for material and personal damage caused by improper

use or non-compliance with the safety instructions! In such cases, the warranty will

be null and void!

Caution!

This product may only be installed by a qualiﬁed technician (e.g., an electrician) who

is familiar with the relevant regulations (e.g., VDE, German electrical wiring regula-

tions)!

Improper work carried out on the mains voltage endangers not only your own life, but

also the life of others!

If you do not have the expertise required for the installation, do not install it yourself

but ask a qualiﬁed technician.

a) General

• The unauthorised conversion and/or modiﬁcation of the product is not permitted for

safety and approval reasons (CE). Do not open/disassemble!

• The product is not a toy and does not belong in the hands of children. There is a risk

of a life-threatening electric shock!

• Do not carelessly leave the packaging material lying around since this may become

a dangerous toy for children.

• Handle the product with care; it may be damaged by impacts, blows, or accidental

falls, even from a low height.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Renkforce RS2W in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,21 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Renkforce RS2W Manual

Product: