485099

Remotec BW0378 - Universal Remote Control Manual

2
Zoom out
Zoom in
Previous page
1/26
Next page
Congratulations! Your Universal Remote Control (URC) is a state-of-the-art
device which integrates many different infra-red remote controls to deliver
instant A/V action to your fingertips.
Before operating the remote, please read thoroughly (1) the interior of the
coversheet and (2) this manual. Then reserve them for future reference.
1 HOW TO INSTALL BATTERIES
Alkaline batteries recommended. The number of battery required stated at
the back of the coversheet.
1. Remove the battery cover on the back of your URC.
2. Observe the polarity of the batteries and the “+/–” marks inside the battery
compartment.
3. Insert the batteries.
4. Push the battery cover back in place.
Battery Low
If the indicator flashes twice slowly after your invoking of any command, it
shows that the battery level is low. You must replace them with new batteries
to ensure proper functioning.
2 HOW TO SET UP THE URC
By entering Device Code
You may setup the URC by the following code entering instructions.
1. Refer to the DEVICE CODE LIST, look up the 4-digit Device Code which
corresponds to the brands of your A/V equipment. If there are more than
one Device Code listed under your brand, try from the first code.
2. Press a desired Device Mode Key (e.g. ).
3. Hold down “ P+ ” and “ VOL– ”on the URC together simultaneously for 2
seconds until the indicator lights up.
4. Use the number keys to enter your 4-digit Device Code, the indi-
cator should go out immediately.
Turn on your device (e.g. TV), try the function keys on the URC. If your device
(e.g. TV) responds to your invoked function correctly, you have entered the
right Device Code. Otherwise, repeat the above setup instructions with the
rest available Device Codes until your device (e.g. TV) responds to your in-
voked function, and most keys work correctly.
* Simply repeat the above procedures to enter the Device Codes for your
VCR, SAT, DVD or CTV. (Remember to press a correct Device Mode Key
in step 2 above)
1
English
Note :
– DVD, CTV and other Device Codes can be entered into any device modes
except “TV” & “VCR” modes. Just simply press the device mode key
and enter your 4-digit device code for DVD, CTV and other devices.
If the indicator flashes twice in step 4, a wrong Device Code has been
entered. You are required to repeat step 2 to 4 again.
Suggestion :
– If you cannot find a correct Device Code for your equipment, see 2 HOW
TO SET UP THE URC– By Seaching Through the Library.
– You are recommended to jot down your Device Codes in the space provided
on back label after setting up the URC correctly for future reference.
TV
2 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Remotec BW0378 - Universal Remote Control at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Remotec BW0378 - Universal Remote Control in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 0,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info