587875
9
Zoom out
Zoom in
Previous page
1/12
Next page
9
L1 L2
I.G.
VEL.
E.I.
6
TERM
C
2
1 2 3 4 5 7 8
MV1
min
med
max
230 V
PE
C1
3-Wege Ventil
2-Leiter Truhe
3-Wege Ventil- Kühlen
4-Leiter Truhe
3-Wege Ventil- Heizen
4-Leiter Truhe
1
L1 L2
1 2 3 4 5 6 7 8
lilabr. bl. rot gr.sw. wß. rs. org.
N
L
Der elektrische Anschluss ist als Festanschluss
auszuführen.
Vor der Installation prüfen, ob die Nennspan-
nung 230 V / 50Hz beträgt.
Stellen Sie sicher, dass die elektrische Anlage
dafür geeignet ist, den zum Betrieb des Gerätes
und den zur Versorgung von anderen bereits
betriebenen Geräten erforderlichen Betriebs-
strom zu liefern.
Die elektrischen Anschlüsse müssen entspre-
chend den geltenden nationalen Bestimmungen
ausgeführt werden.
Vor dem Gerät ist ein allpolig trennender Schal-
ter in die Versorgungsleitung zu installieren.
Das Gerät muß immer geerdet werden!
Anschluss an das Gerät
Die Anschlussleitung von hinten in das Gerät führen.
Die Anschlussklemmen sitzen auf der rechten Geräte-
seite und sind nach dem Entfernen der Gehäusever-
kleidung gut zugänglich. Die Verbindungsleitung ist
entsprechend dem Verdrahtungsplan (Bild 7) am Ge-
rät anzuschließen (L
1
, L
2
und Pe).
Anschluss einer Ventilbaugruppe Kühlen
Für den Fall, dass eine Ventilbaugruppe eingesetzt
wird, kann diese über die Anschlussklemme 1 und 5
an der Klemmeleiste angesteuert werden (gestrichelte
Linie). Bei Kühl- oder Heizanforderung (je nach Be-
triebswahl) liegt dann eine Spannung von 230V / 50
Hz am Ventil an.
Soll nach dem Schließen des Ventils der Ventilator
weiterlaufen, so m die Leitung vom Motor von
Klemme 1 auf die Klemme „L
1
“ (Pfad A) umgelegt wer-
den.
Anschluss der Raumtemperatur-Regelung
Die Raumtemperatur-Regelung wird steckerfertig ge-
liefert. Zur Montage muß erst das Gehäuse demontiert
werden (siehe unter Kapitel 5 Installation, Punkt 3).
Rechts am Rahmen des Gerätes befindet sich die 10-
polige Klemmleiste, in die das Gegenstück von der
Regelung nur eingesteckt werden muß. Oberhalb der
Klemmleiste befinden sich zwei Haltewinkel, in die
wird die Regelung mit ihren vorgesehenen Führungen
0281_02
Bild 7
Pfad A
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for REMKO KLT65 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of REMKO KLT65 in the language / languages: German as an attachment in your email.

The manual is 1,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info