587875
7
Zoom out
Zoom in
Previous page
1/12
Next page
7
Typ
Luftvolu-
menstrom
m³/h
Volumen-
strom
Wasser
m³/h
Druckver-
lust
kPa
Tempera-
tur
Lufteintritt
°C T.K.
Heizleistung [W]
Temperatur Wassereintritt
45°C 50°C 55°C 60°C 65°C 70°C
KLT 30 550
0,30 6,4
20
2700 3100 3500 4100 4700 5100
0,50 17,0 2800 3300 3700 4300 4900 5400
0,55 21,0 3100 3600 4100 4700 5200 5800
KLT 45 700
0,40 6,0
20
3800 4500 5200 5800 6400 7300
0,70 13,0 4200 4900 5600 6300 7000 7700
0,85 19,0 4700 5400 5900 6800 7600 8300
KLT 65 1050
0,60 4,5 5000 5900 6900 7800 8800 9900
0,90 10,0 5400 6300 7300 8300 9300 10400
1,20 18,0 5900 7000 7900 9100 10100 11200
20
Heizleistung
4. Transport
Das Gerät wird in einer stabilen Transportverpackung
aus Karton geliefert. Bitte überprüfen Sie das Gerät
bei der Anlieferung und vermerken Sie eventuelle
Schäden oder fehlende Teile auf dem Lieferschein.
5. Installation
Die Installation darf nur durch autorisiertes Fachperso-
nal vorgenommen werden.
1) Wahl des Installationsortes
Das Innengerät ist für die Wand-, Stand- oder De-
ckenmontage konzipiert. Es ist darauf zu achten,
dass es waagerecht montiert wird um die Funktion
der Kondensatwannen zu gewährleisten.
Die Montageabstände beim Wand- und Deckenge-
rät betragen 90 mm auf der Luftansaugseite (siehe
Bild 1 u. 2).
Für die Montage des Standgerätes müssen erst die
mitgelieferten Füße, wie in Absatz 3) beschrieben
montiert werden.
2) Montage der Füße (nur bei Standgerät)
Entfernen Sie die Verkleidung des Gerätes (Bild 5)
und legen es auf die Rückseite. Schieben Sie nun,
wie in Bild 3 beschrieben die beiden Blechfüße an
den Rahmen des Gerätes und befestigen diese
dann mit den mitgelieferten Schrauben.
Als nächstes werden die Kunststoffverkleidungen
an den Blechfüßen eingeklickt (Bild 4).
Achtung, die rechte Verkleidung hat eine Ausspa-
rung und wird in der zweiten Raste befestigt
(Abstand 70 mm).
Die linke Verkleidung hat keine Aussparung und
wird in der ersten Raste eingeklickt (im Abstand
140 mm).
3) Vorbereitung der Installation
Leitungsführung (Vor-, Rücklauf und Kondensatlei-
tung) planen. Zur Volumenstromregulierung, falls
erforderlich, ein Strangregulierventil (bauseits) im
Rücklauf vorsehen.
Das Gerät aus der Verpackung nehmen und auf
der Vorderseite unten, die zwei Schrauben von der
Befestigung des Gehäuses lösen. Achtung beide
Befestigungsschrauben fixieren gleichzeitig die
Haltewinkel des Ansaugfilter, es ist darauf zu ach-
ten, dass diese beim späteren Verschrauben wie-
der montiert werden.
Nun kann das Gehäuse erst unten abgezogen und
0318_01
Bild 3
0319_01
Bild 4
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for REMKO KLT65 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of REMKO KLT65 in the language / languages: German as an attachment in your email.

The manual is 1,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info