Manual Redmond RI-C222-E (page 5 of 144) (All languages)

659488

Zoom out

Zoom in

1/144

GBR

RI-C222-E

Steam ironing

The most efcient steam ironing can be achieved in • • or • • • temperature modes.

Turn the steam output control dial into the required position. If the dial is in position the

steam feature is disabled (use the mode for dry ironing). Turn the steam output control dial

in direction towards position to increase the steam output.

Plug in the iron. Heating indicator on the housing will light up to indicate the heating. Once

the soleplate reaches the required temperature the heating indicator will go out, indicating

that the iron is ready to use.

NOTE! Constant steam is only generated when the iron is in horizontal position and set to high

temperature. If the steam feature is enabled (the steam output control dial is not in position)

and the temperature setting is too low, water may drip from the soleplate.

Steam Shot

The Steam Shot feature is used to eliminate stubborn wrinkles. The feature can be used

during steam ironing when the heating indicator on the housing is out. If the heating indi-

cator is lit, wait for the soleplate to reach the selected temperature before using the Steam

Shot feature. The Steam output control dial must not be in position.

Briey press the Steam Shot button during ironing for extra steam. Allow an interval of 2-3

seconds between the shots. Steam Shot feature can be used for vertical steaming.

NOTE! When the iron is set to low temperature (• position) water may drip from the soleplate,

the Steam Shot feature may not be applicable.

Vertical steam

The REDMOND RI-C222-E Steam Iron can be used in an upright position to remove wrinkles from

hanging drapes, curtains, tulle, as well as dress clothes without taking them off the hangers.

1. Turn the steam output control dial into position.

2. Turn the temperature control dial into “Max” position.

3. Wait until the soleplate reaches the required temperature (the heating indicator goes out).

4. Hold the iron vertically with the soleplate facing the garment. To avoid burning deli-

cate fabrics hold the iron a few centimeters away from the garment.

5. Move the iron from top to bottom briey pressing the Steam Shot button. Return to

horizontal position every fth time you press the button.

6. If heating indicator lights up, stop steaming and wait for the soleplate to reach the

required temperature. Resume the steaming after the heating indicator goes out.

CAUTION! The iron generates high temperature steam! Do not touch steam to prevent burning.

Never iron clothes on the body!

Dry ironing

You can use the iron for dry ironing even if the water tank is full. However, if using the

feature for a long period of time do not ll the tank with too much water.

1. Turn steam output control dial into position.

2. Turn the temperature control dial to select the temperature appropriate for your fabric.

3. After soleplate reaches selected temperature and heating indicator goes out, the iron

is ready to use.

Water spray feature

Use the water spray feature to dampen hard-to-iron fabrics, remove stubborn wrinkles, and to

iron difcult areas such as collars, etc. Press the water spray button to dampen the fabric:

• slowly and smoothly for a dense spray

• quickly for vaporized spray

The feature can be used as often as required from any temperature mode, as long as there

is enough water in the water tank.

Auto shut-off feature

The auto shut-off feature ensures safety and reduces energy consumption. The iron auto-

matically shuts off when left unattended:

• after 30 seconds of inactivity in horizontal position or on its side (tipped over)

• after 8 minutes of inactivity in vertical position

After the auto shut-off occurs the soleplate stops heating, audible signal is heard, the auto shut-off

indicator on the handle starts ashing. To continue ironing take the iron by the handle. The auto

shut-off indicator will stop ashing, the heating indicator will light up. Once the soleplate reaches

the required temperature the heating indicator will go out, indicating that the iron is ready to use.

Anti-drip feature

The anti-drip feature prevents water from dripping onto fabric and enables to iron even the

most delicate garments. Use low temperature setting (• position) to iron delicate fabrics.

After each use

Turn the temperature control dial into “Min” position and the steam output control dial into

position. Unplug the iron from electrical outlet. Open the water tank cap and gently shake

the iron above the sink to empty the tank. Place the iron into a vertical position.

Wait for the soleplate to cool down thoroughly. Wind the cord around the heel of the iron.

Store in vertical position.

Fabric Ironing Chart

Symbol of the

temperature

mode

Temperature

control dial

position

Fabric Ironing recommendations

•

SYNTHETICS

Acrylic

Iron carefully. Do not use steam iron-

ing to prevent water from dripping

out of soleplate and staining the

fabric

Polyamide (cap-

ron, nylon)

Polyurethane

Acetate

Iron on reverse side, fabric cannot

withstand high heat. Acetate dries fast

and needs little ironing

Polyester Iron using a damp press cloth

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Redmond RI-C222-E in the language / languages: All languages as an attachment in your email.

The manual is 5,84 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Redmond RI-C222-E Manual

Product: