Manual Quadral AURUM A8 (page 5 of 19) (English, German, French, Spanish)

698698

Zoom out

Zoom in

1/19

INSTALLING

1. Select the correct voltage required on the back of the unit amplifier that matches the voltage coming

from the mains supply. Use the power cable supplied in the package to connect the equipment up to the

mains supply.

2. Check that the unit is switched off.

3. Connect up the auxiliary units that you want to use to the equipment‘s inputs. (RCA 1-3, TosLink, SPDIF,

USB) right channel = red / left channel = white or the symmetric analog XLR inputs can be used with any

compatible signal source.

(XLR pin assignments: Pin 1= ground; Pin 2 = plus / signal; Pin 3 = minus)

4. The screw terminals at the back are used for the speaker connections.

5. (See back of the equipment: right channel = 1 / left channel = 7). You must also ensure that the plus

and minus connections on the amplifier concur with the plus and minus connections on the speakers in

order to prevent polarity reversal.

6. Now switch your amplifier own.

Switch the mains switch (9) into the ON position on the back. The standby LED on the front will come

on.

7. Now press the multifunction knob (2) on the front or the button (2) on the remote control to start your

equipment.

Note:

As your A8 uses a special power-saving standby circuit, you can always switch on / off during normal oper-

ation using the multifunction knob on the unit or the RC-2 remote control.

The RC-2 remote control makes it easier for you to change your settings.

Mute (button 3)

Balance setting (buttons 6 & 7)

Multilevel display brilliance setting (button 15)

Input level setting for all inputs (button 14)

Example: Input level setting

Use buttons 8 (-) or 9 (+) to select the signal source and then press button 14 (Prog.) and use the volume

buttons (4 & 5) to set up the input volume to suit yourself. Press button 14 (Prog.) once again to save the

settings.

AMBIENT CONDITIONS

Notes about the removal and the correct environmentally-friendly disposal of old batteries.

The symbol shown here can be found on the equipment‘s enclosure, the packaging as well as in the doc-

uments or the operating manual. It tells you that batteries provided with the equipment as well as those

supplied with or fitted in other units must never be disposed of in household waste. They must be disposed

of in an environmentally-friendly way (in compliance with the local regulations or European Directives

2002/96/EU and 2006/66/EU).

You should find out where the nearest collection point for electronic scrap is or where the recycling site is.

Correct disposal of the equipment and the batteries will help to preserve our resources and prevent physi-

cal and environmental damage. The battery (CR2032) supplied with the remote control contains lithium and

it must be disposed of in an environmentally-friendly way as described above.

Proceed as described in the following section to replace or remove the battery fitted in the remote control.

1. Undo the screw in the cover underneath the remote control and then remove the cover.

2. Remove the battery by sliding it out of its holder.

3. You must ensure that the new battery‘s polarity is correct when you fit the new one! The side of the

battery marked with (+) must point upwards so that it makes contact with the part of the holder marked

with (+).

4. Refit the cover and use the screw to secure it in place.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Quadral AURUM A8 in the language / languages: English, German, French, Spanish as an attachment in your email.

The manual is 0,61 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Quadral AURUM A8 Manual

Product: