698705

Quadral AURUM 9 PASSIV Manual

5
Zoom out
Zoom in
Previous page
1/23
Next page
Subwoofer
Low Level connection
Surround-amplifier
Left
right
8
EN
9
During Bi-wiring / Bi-amping operation of the AURUM loudspeaker, both screw terminals for the woofer (LO)
are below and for the midrange speakers and tweeters (Hl) are above on the connection plate.
Only the largest models of the AURUM 9 series are fitted with an extended connector panel by means of
which these connections are arranged horizontally and the various operating modes apply analogously with
the assignment of (Hl) and (LO).
Make sure you use the correct polarities in these modes and that you remove the jumpers on the speaker
terminal to avoid damaging your amplifier.
OPERATION WITH A SURROUND AMPLIFIER
Once you have positioned and connected your speakers as shown in the illustration, you should perform the
necessary settings in the bass management system of your surround amplifier.
Make sure you read the user manual supplied by your amplifier’s manufacturer before doing this.
Since bass management primarily depends on the loudspeaker configuration, we give only typical settings
below.
a) Small and very small satellite speakers must be operated in “small” mode.
Perform the setting on your amplifier as follows:
Front: small Centre: small
Rear: small Subwoofer: yes
b) There is no definitive formula for the settings for compact speakers. In this case, the suitable mode may be
“large” or “small”. This depends on the volume level you prefer or the sound effect you wish to obtain (refer
to the section “Caution, clipping!”). The settings on your amplifier can optionally be configured as follows:
Front: large/small Centre: large/small
Rear: large/small Subwoofer: yes
c) Floorstanding speakers or large bookshelf speakers that are suitable for powerful bass reproduction
should be operated in “large” mode.
Perform the setting on the amplifier as follows:
Front: large Centre: large
Rear: large Subwoofer: yes/no
Subwoofer
If your surround amplifier has a “line subwoofer” output, you can make use of this by using the Y cable supplied
with the subwoofer (see illustration page 8). In this case, you connect the front speakers directly to the front
speaker terminals of your amplifier. Refer to the connection diagram for wiring your surround system.
Refer to the user manual of the active subwoofer for the necessary settings on your subwoofer!
TIPS FOR BETTER ACOUSTICS
1. The AURUM stand-mounted loudspeakers are fitted with a holder for spikes in order to achieve better
acoustic decoupling of loudspeaker from the floor. Use of spikes can be advantageous dependent on the
nature of the living room and the floor.
AURUM spikes can be obtained separately as an accessory from your dealer.
2. In order to achieve better acoustic decoupling from the mounting surface for shelf or centre speakers, lay
each of these loudspeakers on 4 self-adhesive felt washers.
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Quadral AURUM 9 PASSIV at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Quadral AURUM 9 PASSIV in the language / languages: English, German, French, Spanish as an attachment in your email.

The manual is 1,79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info