698705
4
Zoom out
Zoom in
Previous page
1/23
Next page
CENTER
FRONT
TV
FRONT
SUBWOOFER
REAR
REAR
50 cm
>
REAR
CENTER
CENTER
FRONT
TV
FRONT
SUBWOOFER
REAR
REAR
50 cm
>
+
-
+
-
+
-
+
-
Jumper
Amplifier/
output stage
Amplifier/
output stage
Amplifier/
output stage
Amplifier/
output stage
Tweeter/midrange
Woofer
LO
+
+
-
-
HI
-
+
LO
+
+
-
-
HI
-
+
LO
+
+
-
-
HI
-
+
+
-
+
-
+
-
+
-
Jumper
Amplifier/
output stage
Amplifier/
output stage
Amplifier/
output stage
Amplifier/
output stage
Tweeter/midrange
Woofer
LO
+
+
-
-
HI
-
+
LO
+
+
-
-
HI
-
+
LO
+
+
-
-
HI
-
+
+
-
+
-
+
-
+
-
Jumper
Amplifier/
output stage
Amplifier/
output stage
Amplifier/
output stage
Amplifier/
output stage
Tweeter/midrange
Woofer
LO
+
+
-
-
HI
-
+
LO
+
+
-
-
HI
-
+
LO
+
+
-
-
HI
-
+
6
EN
7
Rear speakers
Whether you direct the rear speakers toward the
listening position is a matter of taste. Also, many
listeners prefer the rear speakers to be positioned
above ear height. This can be achieved by mounting
the units on a sturdy wall bracket, a high speaker
stand, a sideboard or shelf.
STANDS
For optimal front and rear speaker setup, quadral has suitable stands in its product range.
Should you have any questions, please contact us on tel.: +49 (0) 511 7904-0,
e-mail: ovs@quadral.com or info@aurumspeakers.com
CONNECTING TO THE AMPLIFIER
Before connecting up the speakers to your hifi or surround sound system, please ensure that the amplifier/
receiver is switched off and its pilot light is not on. For connection, you will need a twin-core loudspeaker
cable for each speaker cabinet. Make sure these cables are sufficiently long and cut them to a length that will
subsequently enable you to lay them behind furniture or under the carpet where necessary. For cables more
than 5 m in length we recommend a cross-section area of at least 2.5 mm
2
per core in order to avoid any
unnecessary loss of output. To enable optimum contact, about 10 mm of the cores at each end of the cable
must be isolated, and thus bare.
SCREW TERMINALS
For connection, the speakers are provided with colour-coded screw terminals on the back of the cabinet.
Loosen the screw terminals and feed the stripped end of the core into the hole that is now free. The two cores
of speaker cables have different colouring or shape for recognition. Connect the “+” core to the red, positive
terminal – the remaining core to the black terminal. Tighten the screws hand-tight. To ensure correct polarity,
check that the core connected to the red “+” terminal of the speaker is also the core that is connected to the
red “+” terminal of the amplifier and that the other core is
connected to the black “-“ terminals of both the speaker
and amplifier.
With AURUM loudspeakers you can choose between three modes of operation:
a) Conventional mode
Do not remove the jumpers, connect the speaker cable
as shown in the illustration.
b) Biwiring mode
Remove the jumpers after loosening the four screw
terminals on the back of the speaker and connect the
cable as shown in the illustration
c) Biamping mode
Remove the jumpers and connect the cables as shown
in the illustration.
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Quadral AURUM 9 PASSIV at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Quadral AURUM 9 PASSIV in the language / languages: English, German, French, Spanish as an attachment in your email.

The manual is 1,79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info