564082
69
Zoom out
Zoom in
Previous page
1/162
Next page
+ +
+
4
Abnormal combustion:
The flame is yellow and blue In this case take appropriate measures.
This heater cannot be switched on continuously for more than 56 hours. After 56
hours it stops automatically, even if the tank has been refilled within this period.
E SETTING THE REQUIRED TEMPERATURE
If the heater is on, the required temperature can be changed using the adjustment
buttons
20
(fig. K). To increase the temperature, press the button. To decrease
the temperature, press the button. Each time you press the adjustment button
the temperature changes by 1ºC. The temperature can be set to a minimum of
12ºC and a maximum of 26ºC.
If the heater is used in a small space, in a well-insulated space or if the outside
temperature is relatively high, the ambient temperature can become higher
than the required temperature. In this case, turn the heater off.
The displayed temperature is the mean ambient temperature. This
temperature may not correspond with that indicated by a thermometer.
F USING THE TIMER
The timer allows you to switch on the heater automatically at a preset time.
In order to switch on the timer, the correct time must have been set (refer to
Section C) and the heater should be off. Follow the procedure below:
1
Check that the time is set properly (see chapter C).
2
Press the mode button S (fig. L) until Timer and Set appear in the display.
3
Press the () or () buttons to set the required activation time for the
heater. Press the () button to go forwards and the () button to go backwards.
The time will change in one minute steps each time you press one of these 2
buttons. The time on the display will change in ten minute steps if you keep
the button pressed (fig. M).
4
Press the ON / OFF buttons
21
to turn the heater on (the indicator will light up).
It is not necessary to press this button if the heater is on.
5
Press the timer button R. The indicator goes out. The time indicator will light
up and the timer is set.
Take care not to press the ON / OFF button
21
again after setting the timer, this
will reset the timer.
6
The heater turns on at the time chosen.
To cancel the timer, press the ON / OFF button
21
(the timer indicator goes
out).
• Set the timer and the clock again after a power cut.
• In case of an earthquake, or shocks, code E01 will appear in the display. Reset
the error and repeat from point 4 to set the timer again.
69
K
L
M
N
69


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Qlima - Zibro SRE5035C at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Qlima - Zibro SRE5035C in the language / languages: All languages as an attachment in your email.

The manual is 6,75 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Qlima - Zibro SRE5035C

Qlima - Zibro SRE5035C User Manual - Dutch - 18 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info