600480
3
Zoom out
Zoom in
Previous page
1/4
Next page
UNDERSTANDING THE CONTROLS (referring to the
Figure)
ADJUSTING THE DURATION TIME: The length of time that remains
switched on after activation can be adjusted from (10±5) seconds to
(4±1) minutes. Rotating the TIME from (+) to () will reduce the
duration time. Note: Once the light has been triggered by the PIR
sensor any subsequent detection will start the timed period again
from the beginning.
ADJUSTING THE LUX CONTROL LEVEL: The Lux control module has a
built-in sensing device (photocell) that detects daylight and darkness.
The ( ) position denotes that the Floodlights can work at day and
night, and the ( ) position only work at night. You can set to ope-
rate the unit at the desired level by adjusting the LUX knob.
SETTING THE CONTROLS
1. Put the Lux control knob to light ( ) position, turn the wall
switch on and wait half a minute for the control circuit to stabilize.
At this stage ensure that the TIME control knob is set at minimum
(). The light will now switch on and remain on for about 30
seconds (within 60 seconds).
2. Direct the sensor toward the desired area to be scanned by adjus-
ting the sensor.
3. Have another person move across the center of the area to be
scanned and slowly adjust the angle of the sensor until the unit
sensors the presence of the moving person, causing the Light to
switch on. (refer Figure).
4. Adjust time control to required setting.
5. To set the Lux level at which the Light will automatically switch
“on” at night, turn the LUX control knob from daylight to night. If
the Light are required to switch on earlier, e. g. Dusk, wait for the
desired light level, then slowly turn the LUX control knob towards
daylight while someone walks across the center of the area to be
detected. When the Light switch on, release the LUX control knob.
You may need to make further adjustments to achieve your ideal
light level setting.
TECHNICAL DETAILS:
Voltage:
Wattage:
Detection range:
Duration time:
Weatherproof:
Power Cable:
220-240 V ~ 50 Hz
2 ×6 ×0.5W LED
130º and Max. 8 meters
from (10±5) seconds to (4±1) minutes adjustable
IP44
3G, 1.0mm² flexible cable
3
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Qazqa 90501 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Qazqa 90501 in the language / languages: English as an attachment in your email.

The manual is 0,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info