572609

Pulsar Apex LD50 Manual

8
Zoom out
Zoom in
Previous page
1/55
Next page
12 13
Menu М1 includes:
џ Selection of operation mode
џ Selection of calibration mode
џ Weapon selection (1;2;3)
џ Selection of preloaded reticle
џ Brightness control of onscreen symbols
(menu and status bar)
џ Reticle colour selection
џ Function PiP
Menu М2 includes:
џ One shot zeroing
џ “Freeze” zeroing
џ Selection/disable of video output signal
(PAL, NTSC)
џ Clock setup
џ Remote control activation
џ Defective pixel repair option
џ Return to default settings
MENU M1
Operation modes
There are three automatic operating modes:
“Rocks” (enhanced contrast), “Forest” (low contrast) and “Identification”
(improved detail rendering).
Each mode includes optimal combination of parameters (brightness, contrast,
gain etc.) to deliver best possible image in specific viewing conditions.
џ To select an option, press and rotate the controller.
џ Short press of the controller to confirm your choice.
џ Icon of the selected mode is shown in the status bar.
Weapon selection (1,2,3)
This menu option allows selection of three positions of the aiming point for
various types of weapons or for various distances. Also this option allows you
to save three types of reticle for each weapon.
џ To select option, press controller button and select number out of the list
(1; 2; 3).
џ Confirm your choice by a short press of the controller button.
џ Number of the selected variant of the weapon to use is shown in the status
bar in the lower portion of the display.
Note. Originally the reticle for all the three variants is located in the display
centre (coordinates X=0;Y=0). Further on, each type of weapon (distance)
requires individual zeroing.
Selection of calibration mode
Please refer to section 9 “Operation”.
Selection of preloaded reticle
This menu option allows selection of one of the 10 preloaded reticles. Menu
option shows number of the reticle.
џ To select option, press controller button and select reticle number out of the
list. Corresponding reticle will be shown on the display.
џ Confirm your choice by a short press of the controller.
џ List and full description of the reticles can be found at www.pulsar-nv.com
(Support => Download section).
Note: adequate operation of APEX reticles is supported for the basic
magnification for each model (1.5x ; 2x ; 3x), and in the “PiP” mode (“Picture
in Picture”).
Brightness control of onscreen symbols
џ To select option, rotate and press the controller (9).
џ Rotate the controller to select brightness level of icons – from 1 to 10.
џ Confirm your choice by a short press of the controller.
Reticle colour selection
џ To switch between two reticle colours (black or white), press and rotate the
controller.
џ Confirm your choice by a short press of the controller.
Function PiP
Function PiP (“picture in picture”) allows you to enlarge central area of the
reticle twice which facilitates aiming without narrowing the field of view.
џ Select “Yes” to activate the mode. Select “No” to deactivate.
џ Confirm your choice by a short press of the controller.
Note: digital zoom does not work when function PiP is activated.
MENU М2
One shot zeroing
Please refer to section 10 “ZEROING”.
Zeroing with “Freeze” function
Please refer to section 10 “ZEROING”.
Selection/disable of video output signal
џ Press the controller button and rotate it to select output video signal – PAL
or NTSC (video output is disabled by default).
џ To disable the video output, select option “OFF”. Disabled video output
reduces power consumption.
џ Confirm your choice by a short press of the controller button.
Clock setup
џ Press and rotate the controller (9) to select time format: 24/AM/PM.
џ Press the controller to proceed to hour setup. Set the hour value rotating
the controller.
џ Press the controller to proceed to minute setup. Set the minute value.
џ To exit submenu, hold down the controller (9) for two seconds. Or wait ten
seconds to exit automatically.
Remote control activation
Please refer to section 12.
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pulsar Apex LD50 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pulsar Apex LD50 in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 4,97 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info