572609

Pulsar Apex LD50 Manual

6
Zoom out
Zoom in
Previous page
1/55
Next page
8
9
9
EXTERNAL POWER SUPPLY
The sight can be powered with an external DC power supply (2.1mm pin)
with stabilized voltage ranging from 8V to 15V or a 12V vehicle socket.
џ Connect the plug (13) of the cable to the jack (10) of the sight by matching
the notch in the plug connector and the protrusion of the jack (10) (see the
scheme).
џ Secure the cable by turning clockwise the locking ring of the plug (13).
џ Connect the external power supply (AC/DC) or car adapter to the jack (15)
of the cable.
Note: central pin of the power supply that you connect to the “power” jack of
the sight, must have marking “+”.
џ The power supply may have marking .
џ Connection of an external power supply (icon on the status bar)
automatically cuts off power supply from batteries.
џ External power supply DOES NOT charge the batteries in the sight!
Attention! We suggest that you use battery packs EPS3 or EPS5 ensuring
from 9 to 20 hours of continuous operation.
OPERATION
Installation of mount
Before using the sight you need to install the mount (12).
The sight can be used with various mount types such as Weaver, Euro-
prism, Los, Side mount, MAK adapter etc. that allow the scope to be installed
on different types of rifles.
The mounting holes in the base of the sight enable the mount to be installed
in one of the multiple positions. The choice of the mounting position helps the
user to ensure the correct eye relief depending on the rifle type.
џ Attach the mount to the base of the sight using a hex-nut wrench and
screws (see installation scheme).
џ Install the scope on the rifle and check if the position is suitable for you.
џ If you are happy with its position, remove the scope, unscrew the screws
halfway, apply some thread sealant onto the thread of the screws and
tighten them fully (do not overtighten). Let the sealant dry for a while.
џ The sight is ready to be installed on a rifle and to be zeroed.
џ After first installation of your sight on a rifle, please follow instructions in the
section “Zeroing”.
Note. Please check that your sight is duly zeroed after changing a mount.
Powering on and calibration
џ Press briefly the “ON” (1) button to power on the sight. In case of low
battery icon will start flashing.
џ Do the calibration of image. Calibration levels background temperature of
the microbolometer and eliminates image flaws.
џ There are three calibration modes: manual (M), semiautomatic (H) and
automatic (А).
8
Manual (silent) calibration mode
џ The lens cap (8) should be closed.
џ Power on the sight with the “ON” (1) button, hold down the controller (9) for
two seconds to enter the menu.
џ Rotate the controller to select option Cal. Press the controller.
џ Rotate the controller to select mode М. Press the controller to confirm. To
exit the menu, press and hold the controller (9) for two seconds or wait 10
seconds for automatic exit.
џ Press the CAL (2) button to calibrate. The image will freeze for 1-2
seconds. Then open the lens cap. Calibration is completed.
џ In case you see image flaws (such as frozen image, vertical stripes etc.) re-
calibrate the unit with the lens cap closed.
Semiautomatic calibration mode
џ Power on the unit, open the lens cap.
џ Hold down the controller (9) for two seconds to enter the menu.
џ Rotate the controller to select option Cal. Press the controller.
џ Rotate the controller to select mode H. Press the controller to confirm.
џ Press the CAL (2) button to calibrate. The image will freeze for 1-2 seconds
and you will hear the sound of the internal shutter. Calibration is
completed.
Automatic calibration mode
With the automatic calibration mode the thermal imager calibrates by itself
according to the software algorythm. The detector (microbolometer) is
closed with the shutter automatically. User assisted calibration with the CAL
(2) button is allowed in this mode.
џ Power on the unit, open the lens cap.
џ Hold down the controller (9) for two seconds to enter the menu.
џ Rotate the controller to select option Cal. Press the controller.
џ Rotate the controller to select mode A. Press the controller to confirm.
џ At the moment of the automatic calibration the image will freeze for 1-2
seconds and you will hear the sound of the internal shutter.
џ Time intervals between calibrations depend on the heat of the detector.
The unit may require calibration more frequently on activation.
Focusing and image adjustment
џ Open the lens cap (8).
џ Adjust sharp image of the display icons by turning the eyepiece ring (5).
џ To adjust display brightness, rotate the controller (9). Brightness level
(from 0 to 20) will appear next to the brightness icon in the top right
corner of the display.
џ To adjust display contrast, press the controller (icon appears) and rotate
it. Contrast level (from 0 to 20) will appear next to the contrast icon in the
top right corner of the display.
џ Point the unit at a warm object located at a certain distance, 100 meters, for
example.
џ Adjust the focus by turning the ring for lens internal focusing (6).
џ After this adjustment no further dioptre adjustment should be required,
regardless of distance or other factors. Adjust image quality only with the
ring (6) for lens internal focusing.
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pulsar Apex LD50 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pulsar Apex LD50 in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 4,97 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info