527004
4
Zoom out
Zoom in
Previous page
1/9
Next page
B e h e b u n g
B e h e b u n gB e h e b u n g
B e h e b u n g
v o n
v o nv o n
v o n
P r o b l e m e n
P r o b l e m e nP r o b l e m e n
P r o b l e m e n
Problem (mögliche) Ursache Behebung
LED ‘error’ leuchtet
Anschlußdrähte umgepolt
Die Verbindung
entfernen und die
Kabel korrekt anschließen
Die Batterie ist an das
Ladegerät
angeschlossen und das
Ladegerät ist in die
Steckdose gesteckt.
Nür die LED ‘Power on’
brennt.
1. Schlechter Kontakt oder
kein Kontakt zwischen der
Batterie und dem
Ladegerät.
2. Sicherung von des
Ladekabels ist kaputt.
1. Die Verbindung und die
Kabel überprüfen.
2. Auswechsel die Sicherung.
Die Batterie ist an das
Ladegerät
angeschlossen und das
Ladegerät ist in die
Steckdose gesteckt.
Nür die Gelbe LED
brennt.
1. Zu geringe/keine Netz-
spannung
2. Das Ladegerät ist in
einer Thermischer stop.
1. Die Netzspannung
messen; sie sollte höher
sein als 180VAC.
Bei richtiger Netz-
spannung brennt die
Diode ‘Power on’.
2. Die Aufladung werd
automatisch wieder fort-
gesetzt when eine
hinreichende Abkühlung
erzeilt ist.
Die Batterie ist nicht
angeslossen
und Sie messen kein
Spannung
Das Ladegerät mußt einer
gegen Spannung (von eines
Batterie) bekommen bevor
er funktioneert.
Befestig eines Batterie am
Ladegerät.
Das rote oder gelbe LED-
Lämpchen leuchtet nach
einiger Zeit immer noch
1. Die Batterie ist kaputt
2. An die Batterie sind
starke Verbraucher /
schwere Belastungen
angeschlossen.
1. Die Säure auswiegen
und je nach Bedarf die
Batterie auswechseln
2. Schalten Sie so viel
wie möglich Strom-
verbraucher aus.
Wenn der IC-Twin auch nach diesen Maßnahmen immer noch nicht gut funktioniert,
sollten Sie das Ladegerät an Ihren Händler retournieren. Unter keinen Umständen
sollte man versuchen, das Ladegerät selbst zu reparieren oder zu öffnen.
M o n t a g e v o o r s c h r i f t
M o n t a g e v o o r s c h r i f tM o n t a g e v o o r s c h r i f t
M o n t a g e v o o r s c h r i f t
Verwijder aan de voorzijde de plastic beschermfolies.
De laadkabel kan éénmalig gemonteerd worden op de accu. Hierna kunt u heel
eenvoudig d.m.v. de connector (tussen de laadkabel) de lader aan en afkoppelen van
de accu.
1. Koppel de minus kabel eerst af van de accupool alvorens u de kabel gaat
monteren.
2. Houdt het klipje van de connector ingedrukt en trek het uiteinde van de
laadkabel los.
3. Monteer eerst het rode accuvorkje op de + pool van de accu en daarna
het zwarte vorkje op de – pool van de accu.
4. Leidt de kabel zodanig naar een plaats toe waar u de connector
gemakkelijk in elkaar kunt pluggen. Zet de draad goed vast aan het frame.
5. Herstel de verbinding van de minus kabel met de – pool van de accu.
Maak altijd eerst verbinding tussen de acculader en de accu d.m.v. de connector.
Hierna kunt u de lader in een werkend, geaard stopcontact steken. Controleer of het
ledje ‘power on’ en één van de indicatie ledjes gaan branden.
Koppel de acculader eerst af van de netspanning alvorens u de verbinding met de
accu(‘s) verwijdert.
Belangrijk
BelangrijkBelangrijk
Belangrijk
Gebruik altijd de bijgeleverde kabels en connectors
Sluit de lader aan op de accu op een afstand van de brand stofinstallatie.
Vervang beschadigde kabels/connectors direct.
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Proosten IC-TWIN at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Proosten IC-TWIN in the language / languages: English, German, Dutch as an attachment in your email.

The manual is 0,13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info