582126
4
Zoom out
Zoom in
Previous page
1/5
Next page
POWXQ9100 EN
Copyright © 2011 VARO P a g e | 4 www.varo.com
4. Release the rear stability foot lock lever and pivot until it “clicks” into the stored position.
Release the rear leg lock lever and move the rear leg into the stored position. Lock the
rear leg lock lever.
5. The rear carry handle can be used to carry POWXQ9100 when in a folded and upright
orientation. See figs 11 & 12.
6 OPERATION
6.1 Clamping
1. Place the workpiece against the front fixed jaw (2). Slide the moving jaw (2) up against
the workpiece. The moving jaw can either be moved by hand or by using the foot pedal.
2. Slide down the lock / unlock switch to engage the lock. Press down on the foot pedal to
clamp the workpiece. See fig 13.
WARNING: Maximum allowable force on the foot pedal is 100Kg. Do not
stand or jump on the product, as you can cause injury or damage to the
product.
6.2 Releasing
1. Slide up the lock / unlock switch to release the lock.
2. Press down on the foot pedal until it “clicks” to release the clamp.
3. Slide the moving jaw away from the workpiece. See fig 14.
NB: You will need to exert a similar pressure on the foot pedal as was used
to initially clamp the workpiece.
WARNING: Ensure the workpiece is supported to avoid it falling when the
jaw is released.
6.3 Clamping on one side of the jaw
On occasion large or awkward workpieces can only be clamped on one side of the jaws. If this
is the case then avoid excessive use of clamping force. See fig 15.
6.4 Clamping square tube
Clamping square tubing or similar material either on the diagonal or flat side using the grooves
in the jaw pads for alignment.
6.5 Clamping square pieces vertically
On occasion tubing or other square workpieces need to be clamped vertically on the centre of
the jaws. Use the grooves on the jaw pad to align the workpiece. A hole accommodates
workpieces up to 40mm width to be clamped vertically. See fig 16.
6.6 Clamping large objects (clamping range >450mm)
To clamp larger workpieces the moving jaw can be reversed to increase the clamping range,
up to 956mm.
1. Remove the moving jaw by sliding it from the tracks.
2. Rotate the moving jaw 180° and re-assemble. See fig 17.
WARNING: Whenever clamping workpieces up to the maximum clamping
range ensure the work piece rests down on the moving jaw and remains
parallel to it.
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWXQ9100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWXQ9100 in the language / languages: English as an attachment in your email.

The manual is 0,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWXQ9100

Powerplus POWXQ9100 User Manual - German - 5 pages

Powerplus POWXQ9100 User Manual - Dutch - 5 pages

Powerplus POWXQ9100 User Manual - French - 5 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info