481013
6
Zoom out
Zoom in
Previous page
1/9
Next page
POWXQ5223 EN
Copyright © 2014 VARO NV Page| 6 www.varo.com
Insert the bit into the chuck and twist to find the right angle so that the bit can be fully
inserted.
Release the retaining collar, ensuring it returns to its original position.
The bit is now held securely. Some lateral movement may be felt, this is normal for this type of
drill chuck.
7.2 Removing the bit or drill
Slide the retaining collar of the chuck backwards to the end.
Remove the bit from the chuck and release the collar.
Keeping the slotted shank of the bits clean and lightly greased will ensure
they slide in and out the chuck easily.
7.3 Inserting a standard chuck
The tool is supplied with a standard keyed chuck and a SDS adaptor which is fitted exactly the
same way as for bits and chisels. Once fitted, the chuck is only used for non SDS drill bits.
To insert a drill bit:
Open the chuck jaws sufficiently by rotating the chuck sleeve with the key supplied.
Place the drill bit into the jaws as far as it will go.
Close the jaws by rotating the chuck sleeve with the key in the reverse direction.
Make sure the bit is in the center and securely clamped by the jaws.
To remove the bit:
Open the chuck jaws sufficiently by rotating the chuck sleeve with the key.
Remove the bit.
7.4 Installing the auxiliary handle
Turn the knob on the auxiliary handle so as to loosen the steel loop.
Slip the loop onto the neck of the metal housing of the tool.
Position the auxiliary handle at the desired angle and tighten the loop with the knob.
7.5 Setting the depth gauge
Fit the drill bit.
Loosen the knob on the auxiliary handle and slide the depth gauge through the hole on the
auxiliary handle until the distance between the end of the depth gauge and the end of drill
bit is equal to the required depth of the hole to be drilled.
Retighten the knob.
7.6 Dust collection device
Before carrying out hammer-drilling work vertically overhead pull dust collecting device over
the drill bit.
8 OPERATING INSTRUCTIONS
8.1 Switching ON and OFF
To switch on you tool:
Plug the cord set into the power socket.
Press the switch trigger to turn on the tool.
To switch off your tool, just release the trigger switch.
8.2 Operation mode selection
The tool can be set at following operation modes by turning the front and rear mode selectors
to different positions:
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWXQ5223 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWXQ5223 in the language / languages: English as an attachment in your email.

The manual is 0,29 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWXQ5223

Powerplus POWXQ5223 User Manual - German - 10 pages

Powerplus POWXQ5223 User Manual - Dutch - 12 pages

Powerplus POWXQ5223 User Manual - Dutch - 12 pages

Powerplus POWXQ5223 User Manual - French - 10 pages

Powerplus POWXQ5223 Additional guide - All languages - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info