675041

Powerplus POWX1270 Manual

5
Zoom out
Zoom in
Previous page
1/8
Next page
POWX1270 EN
Copyright © 2018 VARO P a g e | 5 www.varo.com
7 ASSEMBLY AND REPLACEMENT INSTRUCTIONS
7.1 Mounting the machine (fig. A)
The machine must be screwed to a workbench.
▪ Mark the position of the mounting holes (8) on the workbench.
▪ Drill holes at each of the marked positions, adjusting the diameter and depth of the holes
to the screws used.
▪ Place the machine on the workbench and insert the screws into the mounting holes.
▪ Firmly tighten the screws,
7.2 Replacing the grinding wheel (fig. B)
▪ Remove the wheel guard (9).
▪ Loosen the nut (10).
▪ Remove the outer flange (11) and the old grinding wheel (3).
▪ Clean the flanges (11 &12).
▪ Place a new grinding wheel.
▪ Place the outer flange against the grinding wheel and place the nut onto the spindle.
Securely tighten the nut.
▪ Replace the wheel guard.
Always unplug the tool before replacing a grinding wheel.
Never use a cracked grinding wheel, Immediately replace a cracked
grinding wheel. A cracked grinding wheel may break into pieces when used
and cause accidents.
7.3 Replacing the sanding belt (fig. C&D)
▪ Remove the belt guard (13).
▪ Loosen the locking knob (14).
▪ Using the lip (16) press the spring (17) to release the tension on the sanding belt (6).
Tighten the locking knob.
▪ Remove the old sanding belt,
▪ Successively place the new sanding belt over the drive roll (18) and the upper roll (19).
▪ Loosen the locking knob and push the upper roll as much to the rear to tension the
sanding belt.
▪ Tighten the locking knob. If necessary adjust the position of the sanding belt by turning the
set screw (15) in or out.
▪ Replace the belt guard,
Always unplug the tool before replacing a sanding belt.
Never use a torn sanding belt. Immediately replace a torn sanding belt. A
torn sanding belt may burst when used and cause accidents.
7.4 Mounting and adjusting the spark guard (fig.E)
The spark guard must be adjusted regularly in order to compensate the wear of the grinding
wheel.
▪ Mount the spark guard (5) to the wheel guard (9) as shown.
▪ Adjust the distance between the spark guard and the grinding wheel (3) to the smallest
possible value, with a maximum of 2 mm.
▪ Tighten the spark guard screw.
▪ Slide the screen (4) to the front,
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWX1270 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWX1270 in the language / languages: English as an attachment in your email.

The manual is 0,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWX1270

Powerplus POWX1270 User Manual - German - 9 pages

Powerplus POWX1270 User Manual - Dutch - 9 pages

Powerplus POWX1270 User Manual - French - 9 pages

Powerplus POWX1270 Additional guide - All languages - 4 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info