Manual Powerplus POWAIR0806 (page 3 of 7) (English)

582125

Zoom out

Zoom in

1/7

POWAIR0806 EN

 To prevent injuries to yourself and bystanders, refer to tool use, maintenance and

troubleshooting sections for additional information (fig 1)

 To prevent eye injuries, always wear safety glasses with hard plastic side shields. Be

sure everyone in your work area is wearing the same type of safety glasses (fig 2)

 Always wear hearing protection and hard hat. (fig 3)

 Never use hydrogen oxygen, carbon dioxide or any other bottled gas as a power

source for this tool, the tool will explode and cause serious injury. (fig4)

 Remove finger from trigger when not driving fasteners. Never carry tool with finger on

trigger, tool will eject fastener If safety is bumped. (fig5)

 Never conned tool to an air hose with pressure exceeds 200 psi or 13.7 BAR (fig6)

 Air compressors must comply with requirement ANSI B19.3 1981 (U.S.), "Safety

Standard For Compressors For Process Industries." (fig 7)

 Air hose minimum working pressure rating of 150 psi (10.3 BAR) or 150% of the

maximum pressure produced in the system is absolutely necessary. (fig 8)

 The tool and air supply hose must have a hose coupling such that all pressure is

removed from the tool when the coupling Joint is disconnected. (fig 9)

 Use only compressed air coming through 3 pieces set. (fig 10)

 Never load fastener before tool connected to air supply (fig 11)

 Never use tool if safety element, trigger or springs have become inoperative, missing or

damaged, It is hazardous to remove safety element, trigger or spring. (fig 12)

 Before using this tool, make sure trigger, screw and cap are securely tightened. (fig 13)

 Do not modify tool without authorization. (fig 14)

 Disconnect tool from air whenever the tool stops working (fig15)

 Keep the tool pointed away from yourself and others. (fig 16)

 Fire fasteners into work surface only, never into materials too hard to penetrate. (fig 17)

 Do not drive fasteners on top of other fasteners. Tool fired in an inclined angle is also

forbidden. (fig 18)

 Do not push safety element on work surface until a second fastener is desired (fig 19)

 Do not drive fasteners close to the edge of the work surface. The work piece is likely to

split and the fastener could fly free and hit someone. (fig 20)

 Do not load fasteners with trigger or safety element depressed. (fig 21)

 Do not use tool without Danger label on tool. (fig 22)

 Never use a tool that leaks air or needs repair. (fig 23)

 Be sure you are in a balanced position when using or handling the tool (fig 24)

 Operate tool at recommended pressure of 4-8 bar

5 LUBRICATION

An automatic in-line filter-regulator-lubricator is recommended (Fig 1) as it increases tool

life and keeps the tool in sustained operation. The in-line lubricator should be regularly

checked and filled with air tool oil.

Proper adjustment of the in-line lubricator is performed by placing a sheet of paper next to

the exhaust ports and holding the throttle open approximately 30 seconds. The lubricator

is properly set when a light stain of oil collects on the paper. Excessive amounts of oil

should be avoided.

In the event that it becomes necessary to store the tool for an extended period of time

(overnight, weekend, etc.), it should receive a generous amount of lubrication at that time.

The tool should be run for approximately 30 seconds to ensure oil has been evenly

distributed throughout the tool. The tool should be stored in a clean and dry environment.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWAIR0806 in the language / languages: English as an attachment in your email.

The manual is 0,25 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWAIR0806

Powerplus POWAIR0806 User Manual - German - 8 pages

Powerplus POWAIR0806 User Manual - Dutch - 8 pages

Powerplus POWAIR0806 User Manual - French - 8 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Powerplus POWAIR0806 Manual

Product: