Manual Polti Sani System Polti Check (page 7 of 13) (English)

648795

Zoom out

Zoom in

1/13

cessible nooks. While it sanitises, it also elim-

inates smells.

Instructions for use :

Fit the disposable bottle into the delivery de-

vice following the instructions in paragraph

“DISPOSABLE BOTTLE OF HPMED”.

Switch on the SANI SYSTEM POLTI ma-

chine following the manufacturer’s instruc-

tions. Once the system is ready, distribute the

steam and HPMED sanitising agent. Mixed

with the steam, the product will dry within 30

seconds to one minute, depending on the en-

vironmental conditions.

Warnings :

Keep out of the reach of children. Do not in-

gest. In case of contact with eyes, rinse with

plenty of water and seek medical advice.

A safety data sheet is available for profes-

sional users.

For professional use only.

HPMED is a cleaning sanitisin product for

hard surfaces. Contains <5% non-ionic sur-

factant. (EEC Reg. 648/2004).

• Unscrew the cap (G) from the tank and fill

the tank with about 4.5l of normal tap water.

Disconnecting of the device from the power

mains before filling is recommended.

• Fit the carrier grip as shown in Fig.1, tighte-

ning the two screws on the rear of the grip

to secure it in place.

• Insert the tube-holder rod (L) into its hole

(Fig.2).

• Plug the power cable (H) into the panel-

type socket on the rear of the device. Plug

the connector on the other end of the power

cord into a suitable socket with an earth

connection.

•

Fit the disposable bottle into the delivery de-

vice following the instructions in paragraph

“DISPOSABLE BOTTLE OF HPMED”.

• Turn the ON-OFF switch (A) to position "I".

• The date and time will appear on the dis-

play (C). Press “OK” on the numerical key-

pad (B) to confirm. If the date and time are

not displayed automatically, it will be neces-

sary to enter them by hand using the nu-

merical keypad and then pressing “OK” to

confirm.

• The prompt “PRINT last logout?” will ap-

pear on the display. Press “OK” on the nu-

merical keypad if you wish to print the lo-

gout summary of the last work session.

Otherwise press “CANC”.

• The device will start up and the word LO-

GIN will appear on the display.

• Insert the CARD (U) into the slot provided

for it (D5).

• The following information will appear:

“HEATING” (flashing) to indicate that the de-

vice is in the heating stage.

Once the correct pressure is reached, the

word “READY” will appear to show that the

device is ready for use.

The indication IDXX will also appear (XX cor-

responds to the number of the CARD inserted

at the time).

N.B.: Do not remove the CARD from the

slot during use.

If the CARD is removed during use, the ma-

chine will stop working and the message

“LOCKED - INSERT CARD IDXX” will appear

on the display. To unlock the machine and re-

sume work, it is necessary to insert the same

card used earlier to log in. The work data will

remain stored in the memory.

The CARDS supplied with the machine are

already configured and will work only in the

machine with which they were supplied. If

new cards are purchased, they will have to be

initialized. To do this, proceed as described in

the section “INITIALISING NEW CARDS”.

• Once you have logged in, the following in-

formation will appear on the display:

“Prog:__” It is necessary to insert the number

of the programme you wish to use. The pro-

gramme numbers have two digits.

There are four pre-set programmes:

00, 01, 02 and 03.

Enter the number of the chosen programme

via the numerical keypad and press OK.

If you have entered the wrong programme

number, you can delete the entry with the

CANC key.

SANI SYSTEM CHECK

SANI SYSTEM CHECK M0S08111 2O08:A5 31/07/2008 11.27 Pagina 45

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Polti Sani System Polti Check in the language / languages: English as an attachment in your email.

The manual is 0,55 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Polti Sani System Polti Check Manual

Product: