133008

Pelgrim gwa 810 Manual

20
Zoom out
Zoom in
Previous page
1/23
Next page
3736
3.1 General
The connection of this appliance to the electric mains must be done by an authorised
installer who is knowledgeable of the safety precautions and will carry them out. The
appliance is in compliance with European guidelines.
Important to know:
• The distance between the lowest point of the exhaust hood and the gas cooker should
be at least 70 cm. When using an electrical cooker this distance should be at least
50 cm.
• The mains voltage indicated on the dataplate on the appliance should be identical to
the mains voltage of the house installation.
• No other appliance must be connected to the duct (such as a hot water heater or a
heater) when the exhaust hood is connected to an existing exhaust duct.
• Please follow the local guidelines with regard to the ventilation of gas appliances.
• The exhaust will operate best when the exhaust pipe is as short and as straight as
possible.
• Check before starting drilling whether there is/are no installation pipe(s) present.
• The connection pipe to the exhaust hood has a diameter of 125 mm or 150 mm.
We recommend that the the exhaust pipe has the same diameter.
• The enclosed installation materials are suitable for reinforced concrete and brick walls.
Special plugs and screws may be required for other materials.
3 Installation
• The main current must be switched off during reparation or cleaning. Remove the
plug from the mains current or turn the switch in the meter cupboard to zero.
• Grease and oil are flammable when they are overheated. Stay in the vicinity of the
cooker when preparing food.
This appliance is marked in accordance with European guideline regarding the
disposal of electrical and electronic appliances (AEEA). This product should be disposed
of in accordance with the local environmental regulations for disposal of waste. For
further information regarding the treatment, recovery and recycling of this product
you can contact your local council, the household waste service or the shop where you
purchased the product.
2.2 Exhaust circuit
Depending on the model there are three possible ways to connect this exhaust hood:
1. As exhaust hood on an exhaust duct. The cooking moisture
that is sucked in and filtered is transported upwards (B1)or,
depending on your choice, to the back (B2) and then to the
outside. This is the best method!
2. As a re-circulation exhaust hood (excluding motorless exhaust
hoods). The grease and odour will be filtered out of the
cooking moisture that is sucked in. The air that is sucked in
is not transported away but blown back into the kitchen (B1).
You will need to fit a carbon filter.
Attention! The carbon filter needs to be ordered separately.
3. As a motorless exhaust hood. This model is only suitable
for installation in combination with a mechanical ventilation
circuit.
2 Safety
… 20 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pelgrim gwa 810 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pelgrim gwa 810 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 2,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info